Cino FM400 manual Code 128 & UCC/EAN 128 Setting

Page 32

Symbology Reading Control

♦ Code 128 & UCC/EAN 128 Setting ♦

PROGRAM

Family Code Selection

P.C

Parameter Selection

F_DEFAULT

Option Code

Mount	Manual
FuzzyScanFixed	Scan
FuzzyScanFixed	Programming

Code 128/EAN-128 Setting

Code 128/EAN-128 Min. Length

Code 128/EAN-128 Max. Length

SS SS SS SS SS SS

SS

MS

SS

MS

Disable Code 128 and UCC/EAN-128

Enable Code 128 and UCC/EAN-128

Disable function code conversion

Enable function code conversion

ISBT Concatenation Off

ISBT Concatenation On

Default (01) 01-Maximum

Scan 2 digits from the option code chart in Appendix, then FuzzyScan will terminate this selection automatically.

Default (98) 98-Minimum

Scan 2 digits from the option code chart in Appendix, then FuzzyScan will terminate this selection automatically.

0

1

2

3

4

5

FIN

(2 digits)

FIN

(2 digits)

28

Image 32

Contents Fixed Mount Scanner Manual Warranty Table of Contents Getting Familiar with Your FuzzyScan Connect to Your Host USB Models FM4xx-11xInstall Your FuzzyScan Adjust Reading AngleUse the Test Mode Test ButtonUse Your FuzzScan ProgrammingFixed Mount ProgrammingManual System Command Bar Code Programming MenuProgramming Procedures Manual Single scan selection Multiple scans selection Cycling scan selection Dual level selection Host Interface Selection Family Code Selection Parameter SelectionSymbol ID 1 character Symbology Reading ControlUser Defined Symbol ID Symbology ID Transmission Option CodeReadable Bar Code Setting Readable Symbology SettingCode 39/Code 32 Setting Code 39 Setting Codabar/NW-7 Setting UPC-A & UPC-E Setting UPC Family SettingUPC-A & UPC-E Setting , Supplement Scan Voting Supplement Scan VotingEAN Setting , Supplement , Supplement Scan Voting EAN Supplement SettingUPC/EAN Security Level EAN Supplement Control UPC/EAN Security Level SettingEAN Supplement Control UCC Coupon Extended Code Setting Iata & Interleaved 2 of 5 Setting Code 25 Family Setting Code 11 & Code 93 Setting MSI/Plessey Setting Code 128 & UCC/EAN 128 Setting UK/Plessey Setting Telepen Setting GS1 DataBar Setting Linear-stacked & Korea Post Code Setting Keyboard Layout Keyboard Layout Language SettingKeyboard Interface Control Record Suffix, Preamble, Postamble & Caps Lock Caps Lock ControlDelay Setting Emulation Setting & Upper/Lower Case Setting Upper/Lower CaseRecord Suffix, Preamble, Postamble Setting Serial Interface ControlDelay Setting Protocol, ACK/NAK Setting Time Out Setting, Baud Rate, Data Frame Serial Response Time-out Baud Rate BPS Data FrameOperation Mode Setting Operation ControlBuzzer, Indicator, Inverse Reading Good Read IndicatorDollar Sign, Redundancy, Scan Rate Control Dollar Sign Control Redundancy Scan Rate ControlReread Delay Double San Verification Good Read Delay Time-out and Duration Setting Scan Input Time-out Hands Free Time-out Good Read DurationPresentation Scanning Setting Presentation SensitivityOK/NG Signal and Beeping Control Programming Preamble, Postamble, Data Length & Symbol ID Trans Condensed DataWizardData Formatter Setting Formatter ControlData Verifier Setting Verifier ControlData Replacer Setting Replacer ControlData Organizer Setting Organizer ControlSelect a Bar Code Symbology Important Notice Data ReplacerData Organizer Symbology ID Table UPC UPC-E EAN/JAN EAN/JAN-13Keyboard Function Code Table HEX/ASCII Reference Table Ascii Input ShortcutExample Operation Mode Quick Set Host Interface Quick SetOption Codes System Commands ENDIndications Fixed Mount Scanner Programming Manual