Barco MFGD 2621, MFGD 3621 user manual Problems and solutions

Page 100

General tips

Problems and solutions

Problem description

Possible tests or solutions

 

 

 

 

Screen remains black

• Please check the installation

 

procedure in this manual

 

• If the LED at the front is orange, the

 

display is in stand-by

 

• Check in the Windows Display

 

Properties if the display controller

 

video heads are attached. If not,

 

there will be no image on the

 

screen.

 

• The external power supply may be

 

defective

 

 

 

Image exhibits noise or

• The video cable may be of poor

interference

quality

 

• DVI video cable may not be firmly

 

connected to the PC or to the

 

display

 

 

Image contains missing

• A number of missing pixels may be

pixels

normal (inherent in LCD technology)

 

 

Image contains not

• You may have installed the driver

enough grayscales

software with an inappropriate

 

selection of Palette Settings (Static

 

Gray with or without System

 

Colors). Install the driver software

 

again using a different setting for

 

Palette Settings.

 

 

The PC does not start up

• Check the CMOS settings in the PC

 

BIOS

 

• The display controller may not be

 

firmly seated in the PCI / AGP

 

connector

 

 

100

Image 100
Contents Coronis 21-inch This page intentionally left blank Copyright notice This page intentionally left blank Table of Contents Locking and unlocking user controls Preface Preface Trademarks FCC notice display Canadian noticeDisposal Information Safety Instructions Safety InstructionsWater and moisture InstallationVentilation This apparatus conforms to Operating precautions How to avoid image retentionNational Scandinavian Deviations for Cl Explanation of symbols Explanation of symbolsSymbols on the display and / or power supply Symbols used throughout the manual This page intentionally left blank Introduction Introduction Single display or complete system? OverviewOverview Features of the BarcoMed Coronis display controller Barcomed Coronis display controller overviewBarcomed Coronis display controller overview Minimum system requirementsSystem Configuration Guidelines Coronis 3MP displaysPower saving Barco displays overviewBarco displays GuardTilt & swivel base Package contents Parts, controls and connectors Parts, controls and connectorsFront G h i j k RearParts, controls and connectors This page intentionally left blank Display controller installation Display controller installation Barcomed Coronis display controller installation Barcomed Coronis display controller installationJumper location Using the VGA capabilities of the BarcoMed Coronis Examples of PCI slotsPCI and RAID Controller Slots Video Outputs BarcoMed PCI Express Controllers Examples of PCI Express SlotsThis page intentionally left blank Display installation Display installation Installation precautions Installation precautionsPrecautions After unpacking the display After unpacking the displayTo remove the clip Adjust the panel orientation To change the panel orientationTilt the panel before rotating After unpacking the display Power connection Power connectionTo connect the power Connecting DVI cables One display Connecting DVI cables Two displaysVideo connection Video connectionUSB connection USB connectionRouting the signal cables Cable routingCable routing To put the foot cover in placeCable routing Attaching the display to an arm stand Attaching the display to an arm standTo attach the display to an arm stand Screws M4 x 8mm Display controller software installation Display controller software installation Display controller software installation Setup.exe, and click Open Reinstalling drivers Automated display configurationUninstalling the drivers and software Click on the file, Setup.exe, and click Open Display controller software installation This page intentionally left blank Page Power off, power save mode, screen saver Avoiding image retentionAvoiding image retention Re-LayoutTo activate appropriate screen saving, proceed as follows This page intentionally left blank Display controller tools Display controller tools Accessing the Barco tab Using the Barco tabBarcoMed control panel operation BarcoMed control panel operationBarco System Report Advanced Properties BarcoMed advanced configurationBarco Drawing Modes Drawing Modes User Modifiable Color PaletteEnable Dithering Device details Monitor ConfigurationGraphics Board Display operation Display operation Operating precautions Stand-by switchingDisplay operation About the On-Screen Display OSD How to navigate through the OSDAbout the on-screen display To disable user controls Locking and unlocking user controlsTo enable user controls Settings menuMain menu Complete OSD overviewLuminance Settings InformationAdvanced display operation IntroductionAdvanced display operation About the Advanced functionsAdvanced functions in the Settings menu Advanced functions in the Luminance menuAdvanced functions in the Information menu Firmware RuntimesMeasurements Scan measurementsAdvanced functions in the Adjustments menu Miscellaneous AdjustmentsMediCal Pro software MediCal Pro software MediCal Pro installation and operation MediCal Pro software installationUsing MediCal Pro MediCal Pro installation and operationMediCal Pro installation and operation Cleaning instructions Cleaning instructions Precautions PrecautionsFront glass Front glassProceed as follows Cabinet CabinetLCD panel LCD panelTo remove the glass panel To clean the LCD panel This page intentionally left blank Troubleshooting Troubleshooting General tips General tipsProblems and solutions Problem description Possible tests or solutions General tips Setting the resolution of your Coronis display PropertiesAdvanced Button 104 Technical Information Technical Information Technical specifications Technical specificationsLight, USB load Technical specifications Altitude Storage Operation 110 Connector pin assignments Connector pin assignmentsDVI connector Glossary GlossaryCalibration Display Controller headWarranty Statement Warranty Statement Article 1 Services Article 2 Items Excluded from Warranty Article 4 Modifications or Changes to the Equipment Article 8 General B4100519-03 March