Barco MFGD 2621, MFGD 3621 user manual Power connection, To connect the power

Page 44

Power connection

Power connection

To connect the power:

(2)

Figure 13

(2)

(3)

Figure 14

1.To get access to the connectors, remove the connector compartment cover by pulling down the 2 clips at the top of the cover.

2.Connect the output of the 12V DC power supply to the DC input of the display.

3.Connect one end of the proper power cable to the AC input of the 12V DC power supply.

4.Connect the other end of the power cord to a grounded power outlet.

44

Image 44
Contents Coronis 21-inch This page intentionally left blank Copyright notice This page intentionally left blank Table of Contents Locking and unlocking user controls Preface Preface Trademarks FCC notice display Canadian noticeDisposal Information Safety Instructions Safety InstructionsVentilation InstallationWater and moisture National Scandinavian Deviations for Cl Operating precautions How to avoid image retentionThis apparatus conforms to Symbols on the display and / or power supply Explanation of symbolsExplanation of symbols Symbols used throughout the manual This page intentionally left blank Introduction Introduction Overview OverviewSingle display or complete system? Features of the BarcoMed Coronis display controller Barcomed Coronis display controller overviewBarcomed Coronis display controller overview Minimum system requirementsSystem Configuration Guidelines Coronis 3MP displaysPower saving Barco displays overviewBarco displays GuardTilt & swivel base Package contents Front Parts, controls and connectorsParts, controls and connectors G h i j k RearParts, controls and connectors This page intentionally left blank Display controller installation Display controller installation Jumper location Barcomed Coronis display controller installationBarcomed Coronis display controller installation Using the VGA capabilities of the BarcoMed Coronis Examples of PCI slotsPCI and RAID Controller Slots Video Outputs BarcoMed PCI Express Controllers Examples of PCI Express SlotsThis page intentionally left blank Display installation Display installation Precautions Installation precautionsInstallation precautions To remove the clip After unpacking the displayAfter unpacking the display Adjust the panel orientation To change the panel orientationTilt the panel before rotating After unpacking the display To connect the power Power connectionPower connection Connecting DVI cables One display Connecting DVI cables Two displaysVideo connection Video connectionUSB connection USB connectionRouting the signal cables Cable routingCable routing To put the foot cover in placeCable routing To attach the display to an arm stand Attaching the display to an arm standAttaching the display to an arm stand Screws M4 x 8mm Display controller software installation Display controller software installation Display controller software installation Setup.exe, and click Open Uninstalling the drivers and software Automated display configurationReinstalling drivers Click on the file, Setup.exe, and click Open Display controller software installation This page intentionally left blank Page Power off, power save mode, screen saver Avoiding image retentionAvoiding image retention Re-LayoutTo activate appropriate screen saving, proceed as follows This page intentionally left blank Display controller tools Display controller tools Accessing the Barco tab Using the Barco tabBarcoMed control panel operation BarcoMed control panel operationBarco System Report Barco Drawing Modes BarcoMed advanced configurationAdvanced Properties Drawing Modes User Modifiable Color PaletteEnable Dithering Graphics Board Monitor ConfigurationDevice details Display operation Display operation Display operation Stand-by switchingOperating precautions About the on-screen display How to navigate through the OSDAbout the On-Screen Display OSD To disable user controls Locking and unlocking user controlsTo enable user controls Settings menuLuminance Complete OSD overviewMain menu Settings InformationAdvanced display operation IntroductionAdvanced display operation About the Advanced functionsAdvanced functions in the Settings menu Advanced functions in the Luminance menuAdvanced functions in the Information menu Firmware RuntimesMeasurements Scan measurementsAdvanced functions in the Adjustments menu Miscellaneous AdjustmentsMediCal Pro software MediCal Pro software MediCal Pro installation and operation MediCal Pro software installationUsing MediCal Pro MediCal Pro installation and operationMediCal Pro installation and operation Cleaning instructions Cleaning instructions Precautions PrecautionsProceed as follows Front glassFront glass Cabinet CabinetTo remove the glass panel LCD panelLCD panel To clean the LCD panel This page intentionally left blank Troubleshooting Troubleshooting General tips General tipsProblems and solutions Problem description Possible tests or solutions General tips Setting the resolution of your Coronis display PropertiesAdvanced Button 104 Technical Information Technical Information Technical specifications Technical specificationsLight, USB load Technical specifications Altitude Storage Operation 110 DVI connector Connector pin assignmentsConnector pin assignments Glossary GlossaryCalibration Display Controller headWarranty Statement Warranty Statement Article 1 Services Article 2 Items Excluded from Warranty Article 4 Modifications or Changes to the Equipment Article 8 General B4100519-03 March