Barco MFGD 3621 Operating precautions How to avoid image retention, This apparatus conforms to

Page 13

Safety Instructions

Operating precautions: How to avoid image retention

Continuous operation of the display with the same image may result in some image sticking on the LCD panel. Over 10 hours operation with the same image content is not recommended.

To decrease the risk of image sticking (image retention):

Switch on DPMS on display and PC

Activate a good screen saver

This apparatus conforms to:

CE (LVD 73/23/EEC), IEC 60950-1, UL 60950-1, CAN/CSA C22.2 No. 60950-1 (c-UL), EN 60950-1 DEMKO, CCC GB4943-1995

National Scandinavian Deviations for Cl. 1.7.2 :

Finland: "Laite on liitettävä suojamaadoituskoskettimilla varustettuun pistorasiaan"

Norway: "Apparatet må tilkoples jordet stikkontakt"

Sweden: "Apparaten skall anslutas till jordat uttag"

13

Image 13
Contents Coronis 21-inch This page intentionally left blank Copyright notice This page intentionally left blank Table of Contents Locking and unlocking user controls Preface Preface FCC notice display Canadian notice TrademarksDisposal Information Safety Instructions Safety InstructionsWater and moisture InstallationVentilation This apparatus conforms to Operating precautions How to avoid image retentionNational Scandinavian Deviations for Cl Explanation of symbols Explanation of symbolsSymbols on the display and / or power supply Symbols used throughout the manual This page intentionally left blank Introduction Introduction Single display or complete system? OverviewOverview Barcomed Coronis display controller overview Features of the BarcoMed Coronis display controllerBarcomed Coronis display controller overview Minimum system requirementsCoronis 3MP displays System Configuration GuidelinesBarco displays overview Power savingBarco displays GuardTilt & swivel base Package contents Parts, controls and connectors Parts, controls and connectorsFront Rear G h i j kParts, controls and connectors This page intentionally left blank Display controller installation Display controller installation Barcomed Coronis display controller installation Barcomed Coronis display controller installationJumper location Examples of PCI slots Using the VGA capabilities of the BarcoMed CoronisPCI and RAID Controller Slots Video Outputs Examples of PCI Express Slots BarcoMed PCI Express ControllersThis page intentionally left blank Display installation Display installation Installation precautions Installation precautionsPrecautions After unpacking the display After unpacking the displayTo remove the clip To change the panel orientation Adjust the panel orientationTilt the panel before rotating After unpacking the display Power connection Power connectionTo connect the power Connecting DVI cables Two displays Connecting DVI cables One displayVideo connection Video connectionUSB connection USB connectionCable routing Routing the signal cablesCable routing To put the foot cover in placeCable routing Attaching the display to an arm stand Attaching the display to an arm standTo attach the display to an arm stand Screws M4 x 8mm Display controller software installation Display controller software installation Display controller software installation Setup.exe, and click Open Reinstalling drivers Automated display configurationUninstalling the drivers and software Click on the file, Setup.exe, and click Open Display controller software installation This page intentionally left blank Page Avoiding image retention Power off, power save mode, screen saverAvoiding image retention Re-LayoutTo activate appropriate screen saving, proceed as follows This page intentionally left blank Display controller tools Display controller tools Using the Barco tab Accessing the Barco tabBarcoMed control panel operation BarcoMed control panel operationBarco System Report Advanced Properties BarcoMed advanced configurationBarco Drawing Modes User Modifiable Color Palette Drawing ModesEnable Dithering Device details Monitor ConfigurationGraphics Board Display operation Display operation Operating precautions Stand-by switchingDisplay operation About the On-Screen Display OSD How to navigate through the OSDAbout the on-screen display Locking and unlocking user controls To disable user controlsSettings menu To enable user controlsMain menu Complete OSD overviewLuminance Information SettingsIntroduction Advanced display operationAdvanced display operation About the Advanced functionsAdvanced functions in the Luminance menu Advanced functions in the Settings menuAdvanced functions in the Information menu Runtimes FirmwareScan measurements MeasurementsMiscellaneous Adjustments Advanced functions in the Adjustments menuMediCal Pro software MediCal Pro software MediCal Pro software installation MediCal Pro installation and operationUsing MediCal Pro MediCal Pro installation and operationMediCal Pro installation and operation Cleaning instructions Cleaning instructions Precautions PrecautionsFront glass Front glassProceed as follows Cabinet CabinetLCD panel LCD panelTo remove the glass panel To clean the LCD panel This page intentionally left blank Troubleshooting Troubleshooting General tips General tipsProblems and solutions Problem description Possible tests or solutions Properties General tips Setting the resolution of your Coronis displayAdvanced Button 104 Technical Information Technical Information Technical specifications Technical specificationsLight, USB load Technical specifications Altitude Storage Operation 110 Connector pin assignments Connector pin assignmentsDVI connector Glossary GlossaryCalibration Display Controller headWarranty Statement Warranty Statement Article 1 Services Article 2 Items Excluded from Warranty Article 4 Modifications or Changes to the Equipment Article 8 General B4100519-03 March