Barco MFGD 2621, MFGD 3621 user manual Water and moisture, Ventilation, Installation

Page 12

Safety Instructions

code: Green-and-yellow: Earth (safety earth), Blue: Neutral,

Brown: Line

Power cord with ANSI 73.11 plug: The wires of the power cord are colored in accordance with the following code: Green/yellow: ground, White: neutral, Black: line (live)

Do not overload wall outlets and extension cords as this may result in fire or electric shock.

Mains lead protection (U.S.: Power cord): Power cords should be routed so that they are not likely to be walked upon or pinched by items placed upon or against them, paying particular attention to cords at plugs and receptacles.

Water and moisture

Never expose the display to rain or moisture.

Never use the display near water - e.g. near a bathtub, washbasin, swimming pool, kitchen sink, laundry tub or in a wet basement.

Ventilation

Do not cover or block the ventilation openings in the cover of the set. When installing the display in a cupboard or another closed location, heed the necessary space between the set and the sides of the cupboard.

Installation

Place the display on a flat, solid and stable surface that can bear the weight of at least 3 displays. If you use an unstable cart or stand, the display may fall, causing serious injury to a child or adult, and serious damage to the equipment.

More warnings in the Installation chapter.

12

Image 12
Contents Coronis 21-inch This page intentionally left blank Copyright notice This page intentionally left blank Table of Contents Locking and unlocking user controls Preface Preface Trademarks FCC notice display Canadian noticeDisposal Information Safety Instructions Safety InstructionsInstallation Water and moistureVentilation Operating precautions How to avoid image retention This apparatus conforms toNational Scandinavian Deviations for Cl Explanation of symbols Explanation of symbolsSymbols on the display and / or power supply Symbols used throughout the manual This page intentionally left blank Introduction Introduction Overview Single display or complete system?Overview Features of the BarcoMed Coronis display controller Barcomed Coronis display controller overviewBarcomed Coronis display controller overview Minimum system requirementsSystem Configuration Guidelines Coronis 3MP displaysPower saving Barco displays overviewBarco displays GuardTilt & swivel base Package contents Parts, controls and connectors Parts, controls and connectorsFront G h i j k RearParts, controls and connectors This page intentionally left blank Display controller installation Display controller installation Barcomed Coronis display controller installation Barcomed Coronis display controller installationJumper location Using the VGA capabilities of the BarcoMed Coronis Examples of PCI slotsPCI and RAID Controller Slots Video Outputs BarcoMed PCI Express Controllers Examples of PCI Express SlotsThis page intentionally left blank Display installation Display installation Installation precautions Installation precautionsPrecautions After unpacking the display After unpacking the displayTo remove the clip Adjust the panel orientation To change the panel orientationTilt the panel before rotating After unpacking the display Power connection Power connectionTo connect the power Connecting DVI cables One display Connecting DVI cables Two displaysVideo connection Video connectionUSB connection USB connectionRouting the signal cables Cable routingCable routing To put the foot cover in placeCable routing Attaching the display to an arm stand Attaching the display to an arm standTo attach the display to an arm stand Screws M4 x 8mm Display controller software installation Display controller software installation Display controller software installation Setup.exe, and click Open Automated display configuration Reinstalling driversUninstalling the drivers and software Click on the file, Setup.exe, and click Open Display controller software installation This page intentionally left blank Page Power off, power save mode, screen saver Avoiding image retentionAvoiding image retention Re-LayoutTo activate appropriate screen saving, proceed as follows This page intentionally left blank Display controller tools Display controller tools Accessing the Barco tab Using the Barco tabBarcoMed control panel operation BarcoMed control panel operationBarco System Report BarcoMed advanced configuration Advanced PropertiesBarco Drawing Modes Drawing Modes User Modifiable Color PaletteEnable Dithering Monitor Configuration Device detailsGraphics Board Display operation Display operation Stand-by switching Operating precautionsDisplay operation How to navigate through the OSD About the On-Screen Display OSDAbout the on-screen display To disable user controls Locking and unlocking user controlsTo enable user controls Settings menuComplete OSD overview Main menuLuminance Settings InformationAdvanced display operation IntroductionAdvanced display operation About the Advanced functionsAdvanced functions in the Settings menu Advanced functions in the Luminance menuAdvanced functions in the Information menu Firmware RuntimesMeasurements Scan measurementsAdvanced functions in the Adjustments menu Miscellaneous AdjustmentsMediCal Pro software MediCal Pro software MediCal Pro installation and operation MediCal Pro software installationUsing MediCal Pro MediCal Pro installation and operationMediCal Pro installation and operation Cleaning instructions Cleaning instructions Precautions PrecautionsFront glass Front glassProceed as follows Cabinet CabinetLCD panel LCD panelTo remove the glass panel To clean the LCD panel This page intentionally left blank Troubleshooting Troubleshooting General tips General tipsProblems and solutions Problem description Possible tests or solutions General tips Setting the resolution of your Coronis display PropertiesAdvanced Button 104 Technical Information Technical Information Technical specifications Technical specificationsLight, USB load Technical specifications Altitude Storage Operation 110 Connector pin assignments Connector pin assignmentsDVI connector Glossary GlossaryCalibration Display Controller headWarranty Statement Warranty Statement Article 1 Services Article 2 Items Excluded from Warranty Article 4 Modifications or Changes to the Equipment Article 8 General B4100519-03 March