Barco MFGD 3621, MFGD 2621 user manual Automated display configuration, Reinstalling drivers

Page 55

Display controller software installation

13.When the driver setup is complete, click the Finish button.

The Barco Product Installation Wizard will now guide you through the installation of MediCal QAWeb, MediCal Pro, or NioWatch, BarcoMed SelfExam, and the Barco on-line documentation.

14.When the Setup complete message appears, select Reboot System Now and click Finish.

Automated display configuration

Once the drivers, software and documentation have been installed and your system has been rebooted, the Barco Monitor Plug and Play Software should automatically detect your Barco displays and attach them to the desktop with the correct resolution. If the Barco Monitor Plug and Play Software fails to detect your Barco displays or fails to attach them to the desktop correctly please refer to the section, Setting the resolution of your CORONIS display on page 102 in the Troubleshooting section of this manual.

Reinstalling drivers

You can install new drivers or reinstall existing drivers at any time by using the Barco Set-up wizard on your Barco system CD-ROM, see

Installing the BARCOMED display controller drivers and software on page 53 of this manual.

Uninstalling the drivers and software

To un-install the BARCO MEDICAL IMAGING DISPLAY SYSTEM drivers, software or documentation, please use the Windows Add/Remove Programs utility. This can be found in the Windows Control Panel.

Note: If you installed your BARCO MEDICAL IMAGING DISPLAY SYSTEM drivers with DualView enabled, the wizard may warn you that DualView must be disabled before the drivers can be un-installed. This is normal, please follow the prompts from the wizard.

55

Image 55
Contents Coronis 21-inch This page intentionally left blank Copyright notice This page intentionally left blank Table of Contents Locking and unlocking user controls Preface Preface FCC notice display Canadian notice TrademarksDisposal Information Safety Instructions Safety InstructionsWater and moisture InstallationVentilation This apparatus conforms to Operating precautions How to avoid image retentionNational Scandinavian Deviations for Cl Explanation of symbols Explanation of symbolsSymbols on the display and / or power supply Symbols used throughout the manual This page intentionally left blank Introduction Introduction Single display or complete system? OverviewOverview Minimum system requirements Features of the BarcoMed Coronis display controllerBarcomed Coronis display controller overview Barcomed Coronis display controller overviewCoronis 3MP displays System Configuration GuidelinesGuard Power savingBarco displays overview Barco displaysTilt & swivel base Package contents Parts, controls and connectors Parts, controls and connectorsFront Rear G h i j kParts, controls and connectors This page intentionally left blank Display controller installation Display controller installation Barcomed Coronis display controller installation Barcomed Coronis display controller installationJumper location Examples of PCI slots Using the VGA capabilities of the BarcoMed CoronisPCI and RAID Controller Slots Video Outputs Examples of PCI Express Slots BarcoMed PCI Express ControllersThis page intentionally left blank Display installation Display installation Installation precautions Installation precautionsPrecautions After unpacking the display After unpacking the displayTo remove the clip To change the panel orientation Adjust the panel orientationTilt the panel before rotating After unpacking the display Power connection Power connectionTo connect the power Video connection Connecting DVI cables One displayConnecting DVI cables Two displays Video connectionUSB connection USB connectionTo put the foot cover in place Routing the signal cablesCable routing Cable routingCable routing Attaching the display to an arm stand Attaching the display to an arm standTo attach the display to an arm stand Screws M4 x 8mm Display controller software installation Display controller software installation Display controller software installation Setup.exe, and click Open Reinstalling drivers Automated display configurationUninstalling the drivers and software Click on the file, Setup.exe, and click Open Display controller software installation This page intentionally left blank Page Re-Layout Power off, power save mode, screen saverAvoiding image retention Avoiding image retentionTo activate appropriate screen saving, proceed as follows This page intentionally left blank Display controller tools Display controller tools BarcoMed control panel operation Accessing the Barco tabUsing the Barco tab BarcoMed control panel operationBarco System Report Advanced Properties BarcoMed advanced configurationBarco Drawing Modes User Modifiable Color Palette Drawing ModesEnable Dithering Device details Monitor ConfigurationGraphics Board Display operation Display operation Operating precautions Stand-by switchingDisplay operation About the On-Screen Display OSD How to navigate through the OSDAbout the on-screen display Locking and unlocking user controls To disable user controlsSettings menu To enable user controlsMain menu Complete OSD overviewLuminance Information SettingsAbout the Advanced functions Advanced display operationIntroduction Advanced display operationAdvanced functions in the Luminance menu Advanced functions in the Settings menuAdvanced functions in the Information menu Runtimes FirmwareScan measurements MeasurementsMiscellaneous Adjustments Advanced functions in the Adjustments menuMediCal Pro software MediCal Pro software MediCal Pro installation and operation MediCal Pro installation and operationMediCal Pro software installation Using MediCal ProMediCal Pro installation and operation Cleaning instructions Cleaning instructions Precautions PrecautionsFront glass Front glassProceed as follows Cabinet CabinetLCD panel LCD panelTo remove the glass panel To clean the LCD panel This page intentionally left blank Troubleshooting Troubleshooting General tips General tipsProblems and solutions Problem description Possible tests or solutions Properties General tips Setting the resolution of your Coronis displayAdvanced Button 104 Technical Information Technical Information Technical specifications Technical specificationsLight, USB load Technical specifications Altitude Storage Operation 110 Connector pin assignments Connector pin assignmentsDVI connector Display Controller head GlossaryGlossary CalibrationWarranty Statement Warranty Statement Article 1 Services Article 2 Items Excluded from Warranty Article 4 Modifications or Changes to the Equipment Article 8 General B4100519-03 March