Brother CM100DM Editing Cutting Lines, EPress the Start/Stop button to start scanning

Page 50

Memo

•In “Direct Cut” mode, the optional 12" × 24" (305 mm × 610 mm) mat and scanning mat cannot be used.

•Before attaching the material to the mat, use a corner of the adhesive side of the mat to test attaching it.

dWhile holding the mat level and lightly inserting it under the feed rollers on the left and

right sides of the feed slot, press in the operation panel.

• For details, see “Loading the Mat” on page 20.

XThe “Start/Stop” button in the operation panel lights up.

ePress the “Start/Stop” button to start scanning.

XWhen scanning is finished, the scanned image appears in the screen.

fCheck the scanned image, and then touch the “OK” key.

■Editing Cutting Lines

aIn the image trim screen, use the touch pen to

touch and drag it around the screen to trim the image.

bTo cut around the image for the pattern, touch the “OK” key.

•Touch to cut any of a variety of shapes as a frame around the scanned image. For details on selecting a frame, see “Advanced Cutting Functions” on page 49.

■Cutting

aTouch the “Cut” key.

XThe “Cut” key is highlighted, and the “Start/Stop” button in the operation panel lights up.

bPress the “Start/Stop” button to start cutting.

•For details on unloading the mat after cutting, follow the procedure under “Unloading the Mat” on page 21.

48

Image 50

Contents Cutting Machine Read Before DOWNLOADING, COPYING, Installing or Using TrademarksIntroduction Important Safety InstructionsSymbols Used in This Document Important NoticePower Supply and AC Adapter Important Safety InstructionsInstallation Location For Safe Operation Unlawful Use of Scanning Equipment Regulation Precautions for ScanningIndustry Canada Compliance Statement For Canada Only Contents Getting StartedScanning Scan mode FeaturesPatterns Pattern mode Scan an imageUnit Descriptions Front Unit Descriptions Rear Getting StartedParts and Functions Unit Descriptions Operation PanelRemoving the Transport Packing Materials Adjusting the Angle of the Operation PanelFirst Steps Turning On/Off the MachineCPress in the operation panel Operation of LCD PanelPreparation of Craft Paper/Fabric BTest attaching the material Lightweight PaperMat and Cutting Blade Combinations CAttach the material to the mat’s adhesive sideAttaching the Material Lightweight Fabric for Quilt Piecing Medium Weight PaperLightweight Fabric for Quilt Piecing Backing light blue Adhesive CPeel off the backing from the top of the support sheetDTest attaching the material Lightweight Fabric for Any Use Other Than Quilt Piecing Contact sheet Backing EPeel off the backing from the contact sheetGlossy side of contact sheet Wrong side of fabric Pattern that was cut out Contact sheet Medium Weight Fabric for Any Use Other Than Quilt PiecingAttaching Fabrics With the Double-Sided Adhesive Cutting Settings Adjusting the Blade ExtensionAdjusting the Cutting Blade Appropriate Blade ExtensionTrial Cutting Installing and Uninstalling the HolderSetting the Holder Turning On the MachineAAttach the material that will be cut to the mat Selecting the Test PatternLoading the Mat Guides Feed rollersCutting Unloading the MatWith an Appropriate Blade Extension With a Blade Extension That Needs to be AdjustedChecking the Trial Cutting Results Machine Settings Settings ScreenPattern Interval Auto ShutdownSeam Allowance Opening ScreenPattern Cutting DEdit the pattern using the pattern editing screenBasic Operations Tutorial 1 Cutting PatternsBSelect the category for the pattern to be cut out Selecting and Editing the Second PatternATouch the Add key in the pattern layout screen CSelect the second pattern to be used DEdit the patternTutorial 2 Cutting Advanced Patterns Selecting and Editing the First Pattern Piece BPeel from the mat the pattern piece that was cut out Cutting the First PatternBPress the Start/Stop button to start cutting Editing and Cutting the Second Pattern Piece Selecting Multiple Patterns Pattern SelectionSelecting a Single Pattern Selecting Desired PatternsSpecifying the Selection Area Pattern Editing Functions Advanced OperationsCutting and Editing Functions Available in the following screenEditing the Pattern Piece Pattern Editing Functions Advanced PatternsPattern Sizing Pattern Layout Screen Layout Editing FunctionsUnifying Grouping Multiple Patterns Welding Merging the Outlines of Multiple PatternsEditing Individual Patterns Welding Merging the Outlines of Multiple PatternsTouch GCheck the preview, and then touch the OK key DTouch in the layout editing screenESelect , and then touch the OK key Auto Layout Functions Scanning a Background ImageEUse the layout editing functions to move the patterns CPress the Start/Stop button to start scanningTouch Material with a cutout displayed as backgroundECheck the character arrangement Character Input FunctionsCType in the characters Recalling Memory FunctionsSaving CTouch the OK key to finish saving the dataRecall from the machine’s memory Recall from a USB flash drivePreparation Drawing FunctionsDrawing Preparing the Pen HolderCutting Around Drawings EAdjust the drawing speed and pressureATouch the pattern to be drawn BAdjust the seam allowance Specifying the Seam AllowanceDTouch the Set key to finish editing the pattern Memo Loading the MaterialCApply the seam allowance ATouch the Draw keyCPress the Start/Stop button to start drawing BAdjust the pen pressureBRemove the pen holder, and then install the blade holder ATouch the Cut keyScanning Scanning FunctionsTutorial 3 Scanning and Cutting FCheck the scanned image, and then touch the OK key Editing Cutting LinesEPress the Start/Stop button to start scanning Outlining and Framing Advanced Cutting FunctionsOutline Distance DPress the Start/Stop button to start scanning Tutorial 4- Creating Cutting DataEditing Cutting Data ASelect the cutting line type in the image editing screenRecalling Cutting Data ASelect the destination where the data will be savedSaving Data BTouch the OK key to finish saving the dataCEdit the cutting data as necessary, and then cut or draw Editing PicturesSpecifying Delete Size Image editing screenSetting Image Detection Level Cutting line created No cutting line createdDTouch to display the scanning settings screen Scanning SpecificationsScan Settings Tutorial 5- Scanning to USBFSelect the size of the scanning area Check the settings, and then touch the OK keyScanning and Saving AAttach the original that will be scanned to the matReplacing the Blade Replacement CriteriaConsumables RemovingBTwist on the holder cap to attach it to the holder InstallingCPull up the holder to leave the blade in the rubber area Cleaning the Mat Care and MaintenanceCleaning Cleaning the HolderCleaning the Scanner Glass Cleaning Inside the MachineCTurn the main power to off, then turn it back to on Adjusting the ScreenFAfter cleaning, perform a test scan NotchPaper/Fabric Jam TroubleshootingPower Supply Cutting Drawing ScanningError Messages Turn the machine off Operation again Data cannot be deleted When the seam allowance setting for a pattern becomesBe an alternative editing method depending on your Project OK to continue?Upgrading the Software Optional AccessoriesCTouch the Update key to start the upgrade 10.11.12 13.14.15 Part Name Part CodeIndex Page Page English 891-Z01 XF5251-001