Brother CM100DM operation manual Unlawful Use of Scanning Equipment

Page 7

Do not fold or stretch the mat with extreme force. If the mat is damaged, it may no longer be possible to cut, draw or scan.

Do not use a damaged mat.

Make sure that the edges of the mat do not become dirty. Otherwise, the mat type cannot be detected, which will interfere with the proper operation of the machine. If the edges become dirty, wipe them with a dry cloth.

Use a mat designed specifically for this machine. In addition, do not use hard materials, such as metal sheets, which are incompatible with this machine. Otherwise, damage to the machine may result.

Avoid using craft paper or fabric covered with decorative layer (that can easily separate), such as lamé or foil. The separate layer may stick to the machine’s scanning device or feed rollers during operation, resulting in damage to the machine. It may also damage the cutting blade.

While the machine is operating, do not pull out or push in the mat with extreme force. Otherwise, the blade or holder may be damaged.

Do not leave material attached to the mat for a long period of time; otherwise, the adhesive will permeate the material.

Store the mat at room temperature and in a location not exposed to high temperatures, high humidity or direct sunlight.

If the carriage must be moved by hand in an emergency, move it slowly. Otherwise, damage to the machine may result.

Before replacing the holder, check that the holder is not moving.

While the machine is operating, do not unplug the power cord or remove the USB flash drive. Otherwise, the USB flash drive may be damaged or the data may be corrupted.

Do not insert foreign objects into the DC power jack or USB port on the machine. Be sure to make space available around them.

Only connect a USB flash drive to the USB port. Otherwise, damage to the machine may result.

Do not touch the screen while the machine is cutting, drawing or scanning.

Do not oil the machine. Otherwise, damage to the machine may result.

Do not use organic solvents, such as thinner, benzene or alcohol, to clean the machine. Otherwise, the finish may peel off or other damage to the machine may result. Clean the machine by wiping it with a soft, dry cloth.

Do not peel off any labels (for example, the serial number label) affixed to the machine.

Unlawful Use of Scanning Equipment

It is an offence to make reproductions of certain items or documents with the intent to commit fraud. The following is a non-exhaustive list of documents which it may be unlawful to produce copies of. We suggest you check with your legal adviser and/or the relevant legal authorities if in doubt about a particular item or document:

Currency

Bonds or other certificates of debt

Certificates of Deposit

Armed forces service or draft papers

Passports

Postage stamps (cancelled or uncancelled)

Immigration papers

Welfare documents

Cheques or drafts drawn by governmental agencies

Identifying badges or insignias

Copyrighted works cannot be copied lawfully, subject to the “fair dealing” exception relating to sections of a copyrighted work. Multiple copies would indicate improper use. Works of art should be considered the equivalent of copyrighted works.

5

Image 7
Contents Cutting Machine Trademarks Read Before DOWNLOADING, COPYING, Installing or UsingImportant Notice Important Safety InstructionsSymbols Used in This Document Introduction Important Safety Instructions Power Supply and AC AdapterInstallation Location For Safe Operation Unlawful Use of Scanning Equipment Industry Canada Compliance Statement For Canada Only Precautions for ScanningRegulation Getting Started ContentsScan an image FeaturesPatterns Pattern mode Scanning Scan modeUnit Descriptions Operation Panel Getting StartedParts and Functions Unit Descriptions Front Unit Descriptions RearTurning On/Off the Machine Adjusting the Angle of the Operation PanelFirst Steps Removing the Transport Packing MaterialsPreparation of Craft Paper/Fabric Operation of LCD PanelCPress in the operation panel CAttach the material to the mat’s adhesive side Lightweight PaperMat and Cutting Blade Combinations BTest attaching the materialLightweight Fabric for Quilt Piecing Medium Weight PaperAttaching the Material Lightweight Fabric for Quilt Piecing DTest attaching the material CPeel off the backing from the top of the support sheetBacking light blue Adhesive Lightweight Fabric for Any Use Other Than Quilt Piecing Glossy side of contact sheet Wrong side of fabric EPeel off the backing from the contact sheetContact sheet Backing Attaching Fabrics With the Double-Sided Adhesive Medium Weight Fabric for Any Use Other Than Quilt PiecingPattern that was cut out Contact sheet Appropriate Blade Extension Adjusting the Blade ExtensionAdjusting the Cutting Blade Cutting SettingsTurning On the Machine Installing and Uninstalling the HolderSetting the Holder Trial CuttingGuides Feed rollers Selecting the Test PatternLoading the Mat AAttach the material that will be cut to the matUnloading the Mat CuttingChecking the Trial Cutting Results With a Blade Extension That Needs to be AdjustedWith an Appropriate Blade Extension Settings Screen Machine SettingsOpening Screen Auto ShutdownSeam Allowance Pattern IntervalTutorial 1 Cutting Patterns DEdit the pattern using the pattern editing screenBasic Operations Pattern CuttingCSelect the second pattern to be used DEdit the pattern Selecting and Editing the Second PatternATouch the Add key in the pattern layout screen BSelect the category for the pattern to be cut outTutorial 2 Cutting Advanced Patterns Selecting and Editing the First Pattern Piece BPress the Start/Stop button to start cutting Cutting the First PatternBPeel from the mat the pattern piece that was cut out Editing and Cutting the Second Pattern Piece Selecting Desired Patterns Pattern SelectionSelecting a Single Pattern Selecting Multiple PatternsSpecifying the Selection Area Available in the following screen Advanced OperationsCutting and Editing Functions Pattern Editing FunctionsPattern Sizing Pattern Editing Functions Advanced PatternsEditing the Pattern Piece Layout Editing Functions Pattern Layout ScreenWelding Merging the Outlines of Multiple Patterns Welding Merging the Outlines of Multiple PatternsEditing Individual Patterns Unifying Grouping Multiple PatternsESelect , and then touch the OK key DTouch in the layout editing screenTouch GCheck the preview, and then touch the OK key Scanning a Background Image Auto Layout FunctionsMaterial with a cutout displayed as background CPress the Start/Stop button to start scanningTouch EUse the layout editing functions to move the patternsCType in the characters Character Input FunctionsECheck the character arrangement CTouch the OK key to finish saving the data Memory FunctionsSaving RecallingRecall from a USB flash drive Recall from the machine’s memoryPreparing the Pen Holder Drawing FunctionsDrawing PreparationSpecifying the Seam Allowance EAdjust the drawing speed and pressureATouch the pattern to be drawn BAdjust the seam allowance Cutting Around DrawingsATouch the Draw key Loading the MaterialCApply the seam allowance DTouch the Set key to finish editing the pattern MemoATouch the Cut key BAdjust the pen pressureBRemove the pen holder, and then install the blade holder CPress the Start/Stop button to start drawingTutorial 3 Scanning and Cutting Scanning FunctionsScanning EPress the Start/Stop button to start scanning Editing Cutting LinesFCheck the scanned image, and then touch the OK key Outline Distance Advanced Cutting FunctionsOutlining and Framing ASelect the cutting line type in the image editing screen Tutorial 4- Creating Cutting DataEditing Cutting Data DPress the Start/Stop button to start scanningBTouch the OK key to finish saving the data ASelect the destination where the data will be savedSaving Data Recalling Cutting DataImage editing screen Editing PicturesSpecifying Delete Size CEdit the cutting data as necessary, and then cut or drawCutting line created No cutting line created Setting Image Detection LevelTutorial 5- Scanning to USB Scanning SpecificationsScan Settings DTouch to display the scanning settings screenAAttach the original that will be scanned to the mat Check the settings, and then touch the OK keyScanning and Saving FSelect the size of the scanning areaRemoving Replacement CriteriaConsumables Replacing the BladeCPull up the holder to leave the blade in the rubber area InstallingBTwist on the holder cap to attach it to the holder Cleaning the Holder Care and MaintenanceCleaning Cleaning the MatCleaning Inside the Machine Cleaning the Scanner GlassNotch Adjusting the ScreenFAfter cleaning, perform a test scan CTurn the main power to off, then turn it back to onPower Supply TroubleshootingPaper/Fabric Jam Cutting Scanning DrawingError Messages OK to continue? When the seam allowance setting for a pattern becomesBe an alternative editing method depending on your Project Turn the machine off Operation again Data cannot be deleted10.11.12 13.14.15 Part Name Part Code Optional AccessoriesCTouch the Update key to start the upgrade Upgrading the SoftwareIndex Page Page English 891-Z01 XF5251-001