Brother CM100DM operation manual Upgrading the Software, Optional Accessories

Page 68

UPGRADING THE SOFTWARE

Using a USB flash drive, the machine’s software can be upgraded. For upgrade information, refer to details posted on the Brother Solutions Center (http:// solutions.brother.com/). If an upgrade file is posted, download the file, and then upgrade the machine according to the following procedure.

aWhile holding down in the operation

panel, press to turn on the machine.

bPlug the USB flash drive containing the upgrade file into the USB port on this machine.

The USB flash drive must not contain any data other than the upgrade file. Otherwise, the machine may stop operating correctly.

Note

•This machine is incompatible with a USB hub. Plug the USB flash drive directly into the USB port.

cTouch the “Update” key to start the upgrade.

XWhen upgrading is finished, the completion message appears.

dUnplug the USB flash drive from the port. eTurn the machine off, then on again.

OPTIONAL ACCESSORIES

The following are available as optional accessories to be purchased separately.

1.2.3.

4.5.6.

7.8.9.

10.11.12.

13.14.15.

No.

Part Name

Part Code

1

Low tack adhesive mat 12" × 12"

CAMATP12

(305 mm × 305 mm) (turquoise)

 

 

2

Low tack adhesive mat 12" × 24"

CAMATP24

(305 mm × 610 mm) (turquoise)

 

 

3

Standard cut blade holder

CAHLP1

(turquoise) (with no blade)

 

 

4

Standard cut blade

CABLDP1

5

Scanning mat 12" × 12"

CAMATS12

(305 mm × 305 mm)

 

 

 

Standard mat 12" × 12"

 

6

(305 mm × 305 mm)

CAMATF12

 

(turquoise and purple)

 

 

Standard mat 12" × 24"

 

7

(305 mm × 610 mm)

CAMATF24

 

(turquoise and purple)

 

8

Deep cut blade holder (purple)

CAHLF1

(with no blade)

 

 

9

Deep cut blade

CABLDF1

10

Pen holder

CAPENHL1

11

Color pen set

CAPEN1

12

Erasable pen set

CAPEN2

13

Contents USB

*

14

Iron-on fabric appliqué contact

CASTBL1

sheet (white backing)

 

 

15

High tack adhesive fabric support

CASTBL2

sheet (light blue backing)

 

 

*Contact the retailer who sold you this machine or the nearest authorized service center.

66

Page 67 Page 69
Image 68
Page 67 Page 69
Contents Cutting Machine Read Before DOWNLOADING, COPYING, Installing or Using TrademarksImportant Safety Instructions Symbols Used in This DocumentIntroduction Important NoticePower Supply and AC Adapter Important Safety InstructionsInstallation Location For Safe Operation Unlawful Use of Scanning Equipment Regulation Precautions for ScanningIndustry Canada Compliance Statement For Canada Only Contents Getting StartedFeatures Patterns Pattern modeScanning Scan mode Scan an imageGetting Started Parts and FunctionsUnit Descriptions Front Unit Descriptions Rear Unit Descriptions Operation PanelAdjusting the Angle of the Operation Panel First StepsRemoving the Transport Packing Materials Turning On/Off the MachineCPress in the operation panel Operation of LCD PanelPreparation of Craft Paper/Fabric Lightweight Paper Mat and Cutting Blade CombinationsBTest attaching the material CAttach the material to the mat’s adhesive sideAttaching the Material Lightweight Fabric for Quilt Piecing Medium Weight PaperLightweight Fabric for Quilt Piecing Backing light blue Adhesive CPeel off the backing from the top of the support sheetDTest attaching the material Lightweight Fabric for Any Use Other Than Quilt Piecing Contact sheet Backing EPeel off the backing from the contact sheetGlossy side of contact sheet Wrong side of fabric Pattern that was cut out Contact sheet Medium Weight Fabric for Any Use Other Than Quilt PiecingAttaching Fabrics With the Double-Sided Adhesive Adjusting the Blade Extension Adjusting the Cutting BladeCutting Settings Appropriate Blade ExtensionInstalling and Uninstalling the Holder Setting the HolderTrial Cutting Turning On the MachineSelecting the Test Pattern Loading the MatAAttach the material that will be cut to the mat Guides Feed rollersCutting Unloading the MatWith an Appropriate Blade Extension With a Blade Extension That Needs to be AdjustedChecking the Trial Cutting Results Machine Settings Settings ScreenAuto Shutdown Seam AllowancePattern Interval Opening ScreenDEdit the pattern using the pattern editing screen Basic OperationsPattern Cutting Tutorial 1 Cutting PatternsSelecting and Editing the Second Pattern ATouch the Add key in the pattern layout screenBSelect the category for the pattern to be cut out CSelect the second pattern to be used DEdit the patternTutorial 2 Cutting Advanced Patterns Selecting and Editing the First Pattern Piece BPeel from the mat the pattern piece that was cut out Cutting the First PatternBPress the Start/Stop button to start cutting Editing and Cutting the Second Pattern Piece Pattern Selection Selecting a Single PatternSelecting Multiple Patterns Selecting Desired PatternsSpecifying the Selection Area Advanced Operations Cutting and Editing FunctionsPattern Editing Functions Available in the following screenEditing the Pattern Piece Pattern Editing Functions Advanced PatternsPattern Sizing Pattern Layout Screen Layout Editing FunctionsWelding Merging the Outlines of Multiple Patterns Editing Individual PatternsUnifying Grouping Multiple Patterns Welding Merging the Outlines of Multiple PatternsTouch GCheck the preview, and then touch the OK key DTouch in the layout editing screenESelect , and then touch the OK key Auto Layout Functions Scanning a Background ImageCPress the Start/Stop button to start scanning TouchEUse the layout editing functions to move the patterns Material with a cutout displayed as backgroundECheck the character arrangement Character Input FunctionsCType in the characters Memory Functions SavingRecalling CTouch the OK key to finish saving the dataRecall from the machine’s memory Recall from a USB flash driveDrawing Functions DrawingPreparation Preparing the Pen HolderEAdjust the drawing speed and pressure ATouch the pattern to be drawn BAdjust the seam allowanceCutting Around Drawings Specifying the Seam AllowanceLoading the Material CApply the seam allowanceDTouch the Set key to finish editing the pattern Memo ATouch the Draw keyBAdjust the pen pressure BRemove the pen holder, and then install the blade holderCPress the Start/Stop button to start drawing ATouch the Cut keyScanning Scanning FunctionsTutorial 3 Scanning and Cutting FCheck the scanned image, and then touch the OK key Editing Cutting LinesEPress the Start/Stop button to start scanning Outlining and Framing Advanced Cutting FunctionsOutline Distance Tutorial 4- Creating Cutting Data Editing Cutting DataDPress the Start/Stop button to start scanning ASelect the cutting line type in the image editing screenASelect the destination where the data will be saved Saving DataRecalling Cutting Data BTouch the OK key to finish saving the dataEditing Pictures Specifying Delete SizeCEdit the cutting data as necessary, and then cut or draw Image editing screenSetting Image Detection Level Cutting line created No cutting line createdScanning Specifications Scan SettingsDTouch to display the scanning settings screen Tutorial 5- Scanning to USBCheck the settings, and then touch the OK key Scanning and SavingFSelect the size of the scanning area AAttach the original that will be scanned to the matReplacement Criteria ConsumablesReplacing the Blade RemovingBTwist on the holder cap to attach it to the holder InstallingCPull up the holder to leave the blade in the rubber area Care and Maintenance CleaningCleaning the Mat Cleaning the HolderCleaning the Scanner Glass Cleaning Inside the MachineAdjusting the Screen FAfter cleaning, perform a test scanCTurn the main power to off, then turn it back to on NotchPaper/Fabric Jam TroubleshootingPower Supply Cutting Drawing ScanningError Messages When the seam allowance setting for a pattern becomes Be an alternative editing method depending on your ProjectTurn the machine off Operation again Data cannot be deleted OK to continue?Optional Accessories CTouch the Update key to start the upgradeUpgrading the Software 10.11.12 13.14.15 Part Name Part CodeIndex Page Page English 891-Z01 XF5251-001
Top Page Image Contents