Brother CM100DM Be an alternative editing method depending on your Project, OK to continue?

Page 67

Error Messages

Causes / Solutions

 

 

The message appears when you are welding patterns.

 

 

- The patterns do not overlap. Rearrange them so the

 

 

selected patterns overlap. Unifying the pattern, instead,

 

 

can be an alternative editing method depending on your

 

 

project.

 

Patterns cannot be welded.

- A pattern that has a seam allowance is selected.

 

There are some patterns which cannot accept or no overlaps.

Deactivate the seam allowance setting and weld the

 

 

patterns.

 

 

- An open shape is selected as a pattern. Only closed

 

 

shapes can be welded. Unifying the pattern, instead, can

 

 

be an alternative editing method depending on your

 

 

project.

 

 

 

 

Patterns may overlap since seam allowance is set to large on

When the seam allowance setting for a pattern becomes

 

larger than with a previous operation, the edges may overlap

 

the machine.

nearby patterns. Adjust the seam allowance setting.

 

 

Otherwise, increase the spacing between patterns.

 

 

 

 

Scanning error occurred.

Turn the machine off, then on again, and then try performing

 

Turn the machine off.

the operation again.

 

 

 

 

The data cannot be deleted.

The USB flash drive being used may not be usable with this

 

machine. If unplugging the USB flash drive and performing

 

 

5

The data cannot be read.

the operation again causes the message to appear again,

replace the USB flash drive. For information about USB flash

 

The data cannot be saved.

drive compatible with this machine, visit our website

 

“ http://solutions.brother.com ”.

 

 

 

 

 

 

 

A mat that cannot be recognized has been inserted. If a mat

 

 

designed specifically for this machine is not being used, use

 

The mat cannot be recognized.

the specially designed mat.

 

The mat will unload.

Clean the dotted marks at the edge of the mat and their

 

 

surrounding area. If the mat is still not recognized, replace

 

 

the mat with a new one.

 

 

 

 

There are some patterns which cannot add seam allowance.

The seam allowance settings cannot be specified for

 

 

complex pattern shapes. Select a pattern with a simple

 

 

 

There are some patterns which cannot set cutting distance

shape.

 

Expanding the seam allowance (shadow) to 2 mm or more

 

from the outline.

 

 

may help.

 

There is a pattern included that cannot be saved to USB

Depending on the pattern, it may not be possible to save it to

 

media.

 

a USB flash drive.

 

Save the pattern in the machine’s memory.

 

 

 

 

 

 

 

There is a pattern(s) outside of the cutting area.

 

There is a pattern out of the effective area. The pattern

If the pattern(s) outside of the cutting area need(s) not to be

 

cut out or drawn, continue the operation.

 

cannot be cut or drawn.

 

To cut out or draw the pattern(s) outside of the area, increase

 

OK to continue?

 

the setting for “Cut Area”, or move the pattern(s) into the area

 

 

 

 

specified with “Cut Area” (page 23).

 

 

 

 

This data is too complicated and cannot be converted.

When your are welding or unifying patterns:

 

Reduce the number of patterns arranged or change the

 

 

patterns to ones with simple designs.

 

 

 

 

This mat cannot be used.

The mat is one that cannot be used with the function being

 

performed. Replace the mat.

 

 

 

 

 

 

65

Page 66 Page 68
Image 67
Page 66 Page 68
Contents Cutting Machine Trademarks Read Before DOWNLOADING, COPYING, Installing or UsingImportant Notice Important Safety InstructionsSymbols Used in This Document IntroductionImportant Safety Instructions Power Supply and AC AdapterInstallation Location For Safe Operation Unlawful Use of Scanning Equipment Industry Canada Compliance Statement For Canada Only Precautions for ScanningRegulation Getting Started ContentsScan an image FeaturesPatterns Pattern mode Scanning Scan modeUnit Descriptions Operation Panel Getting StartedParts and Functions Unit Descriptions Front Unit Descriptions RearTurning On/Off the Machine Adjusting the Angle of the Operation PanelFirst Steps Removing the Transport Packing MaterialsPreparation of Craft Paper/Fabric Operation of LCD PanelCPress in the operation panel CAttach the material to the mat’s adhesive side Lightweight PaperMat and Cutting Blade Combinations BTest attaching the materialLightweight Fabric for Quilt Piecing Medium Weight PaperAttaching the Material Lightweight Fabric for Quilt Piecing DTest attaching the material CPeel off the backing from the top of the support sheetBacking light blue Adhesive Lightweight Fabric for Any Use Other Than Quilt Piecing Glossy side of contact sheet Wrong side of fabric EPeel off the backing from the contact sheetContact sheet Backing Attaching Fabrics With the Double-Sided Adhesive Medium Weight Fabric for Any Use Other Than Quilt PiecingPattern that was cut out Contact sheet Appropriate Blade Extension Adjusting the Blade ExtensionAdjusting the Cutting Blade Cutting SettingsTurning On the Machine Installing and Uninstalling the HolderSetting the Holder Trial CuttingGuides Feed rollers Selecting the Test PatternLoading the Mat AAttach the material that will be cut to the matUnloading the Mat CuttingChecking the Trial Cutting Results With a Blade Extension That Needs to be AdjustedWith an Appropriate Blade Extension Settings Screen Machine SettingsOpening Screen Auto ShutdownSeam Allowance Pattern IntervalTutorial 1 Cutting Patterns DEdit the pattern using the pattern editing screenBasic Operations Pattern CuttingCSelect the second pattern to be used DEdit the pattern Selecting and Editing the Second PatternATouch the Add key in the pattern layout screen BSelect the category for the pattern to be cut outTutorial 2 Cutting Advanced Patterns Selecting and Editing the First Pattern Piece BPress the Start/Stop button to start cutting Cutting the First PatternBPeel from the mat the pattern piece that was cut out Editing and Cutting the Second Pattern Piece Selecting Desired Patterns Pattern SelectionSelecting a Single Pattern Selecting Multiple PatternsSpecifying the Selection Area Available in the following screen Advanced OperationsCutting and Editing Functions Pattern Editing FunctionsPattern Sizing Pattern Editing Functions Advanced PatternsEditing the Pattern Piece Layout Editing Functions Pattern Layout ScreenWelding Merging the Outlines of Multiple Patterns Welding Merging the Outlines of Multiple PatternsEditing Individual Patterns Unifying Grouping Multiple PatternsESelect , and then touch the OK key DTouch in the layout editing screenTouch GCheck the preview, and then touch the OK key Scanning a Background Image Auto Layout FunctionsMaterial with a cutout displayed as background CPress the Start/Stop button to start scanningTouch EUse the layout editing functions to move the patternsCType in the characters Character Input FunctionsECheck the character arrangement CTouch the OK key to finish saving the data Memory FunctionsSaving RecallingRecall from a USB flash drive Recall from the machine’s memoryPreparing the Pen Holder Drawing FunctionsDrawing PreparationSpecifying the Seam Allowance EAdjust the drawing speed and pressureATouch the pattern to be drawn BAdjust the seam allowance Cutting Around DrawingsATouch the Draw key Loading the MaterialCApply the seam allowance DTouch the Set key to finish editing the pattern MemoATouch the Cut key BAdjust the pen pressureBRemove the pen holder, and then install the blade holder CPress the Start/Stop button to start drawingTutorial 3 Scanning and Cutting Scanning FunctionsScanning EPress the Start/Stop button to start scanning Editing Cutting LinesFCheck the scanned image, and then touch the OK key Outline Distance Advanced Cutting FunctionsOutlining and Framing ASelect the cutting line type in the image editing screen Tutorial 4- Creating Cutting DataEditing Cutting Data DPress the Start/Stop button to start scanningBTouch the OK key to finish saving the data ASelect the destination where the data will be savedSaving Data Recalling Cutting DataImage editing screen Editing PicturesSpecifying Delete Size CEdit the cutting data as necessary, and then cut or drawCutting line created No cutting line created Setting Image Detection LevelTutorial 5- Scanning to USB Scanning SpecificationsScan Settings DTouch to display the scanning settings screenAAttach the original that will be scanned to the mat Check the settings, and then touch the OK keyScanning and Saving FSelect the size of the scanning areaRemoving Replacement CriteriaConsumables Replacing the BladeCPull up the holder to leave the blade in the rubber area InstallingBTwist on the holder cap to attach it to the holder Cleaning the Holder Care and MaintenanceCleaning Cleaning the MatCleaning Inside the Machine Cleaning the Scanner GlassNotch Adjusting the ScreenFAfter cleaning, perform a test scan CTurn the main power to off, then turn it back to onPower Supply TroubleshootingPaper/Fabric Jam Cutting Scanning DrawingError Messages OK to continue? When the seam allowance setting for a pattern becomesBe an alternative editing method depending on your Project Turn the machine off Operation again Data cannot be deleted10.11.12 13.14.15 Part Name Part Code Optional AccessoriesCTouch the Update key to start the upgrade Upgrading the SoftwareIndex Page Page English 891-Z01 XF5251-001
Top Page Image Contents