Pioneer 3TM, 2TM manual

Page 2

Copyright © 2003, ActivMedia Robotics, LLC. All rights reserved.

Under international copyright laws, this manual or any portion of it may not be copied or in any way duplicated without the expressed written consent of ActivMedia Robotics.

The software on disk, CD-ROM, and/or in the microcontroller’s FLASH, which accompany the robot and are available for network download by ActivMedia Robotics customers, are solely owned and copyrighted or are licensed products distributed by ActivMedia Robotics, LLC.

Developers and users are authorized by revocable license to develop and operate custom software for personal research and educational use only. Duplication, distribution, reverse-engineering, or commercial application of the ActivMedia Robotics software and hardware without the expressed written consent of ActivMedia Robotics, LLC, is explicitly forbidden.

The various names and logos for products used in this manual are often registered trademarks or trademarks of their respective companies. Mention of any third-party hardware or software constitutes neither an endorsement nor a recommendation.

Pioneer 3 & Pioneer 2 H8-Series Operations Manual, version 3, August 2003

ii

Image 2

Contents Pioneer H8-Series Operations Manual Page Important Safety Instructions Table of Contents Operating the Aria Demonstration Client Appendix C Basic Components all shipments IntroductionRobot Package Optional Components and Attachments partial listSupport Website User-Supplied Components / System RequirementsAdditional Resources NewsgroupsSupport Support@activmedia.comWhat Is Pioneer? Pioneer Reference PlatformPlus MOTOR-POWER Board Hitachi H8S-BASED MicrocontrollerClient Software Http//robots.activmedia.comSupporting Software Pioneer LegacyPioneer 1 and AT Pioneer 2 and PeopleBotActivMedia Robotics Modes of Operation Server ModeMaintenance and Standalone Modes Joydrive and Self Test ModesSpecifications & Controls Physical CharacteristicsMain Components Motor Stop ButtonUser Control Panel P3-DX User Control PanelBody, Nose, and Accessory Panels Sonar Arrays with Gain AdjustmentBatteries and Power Motors, Wheels, and Position EncodersBattery Indicators and Low Voltage Conditions RechargingDOCKING/CHARGING System Manual Operation Robot Power OFFManual Operation Robot Power and Systems on Radio Controls and Accessories Client-server connection optionsOnboard PC Computer Control PanelOperating the Onboard PC PC NetworkingUPS and Genpowerd Safety Aros Watchdogs Quick Start Preparative AssemblyInstall Aria Starting UP Client and Server Install BatteriesClient-Server Communications Drive Self-TestDemo Startup Options IpthruSuccessful Connection Operating the Aria Demonstration ClientProper Connections DisconnectingQuickstart Troubleshooting OFF SRIsimJoydrive Mode Joydrive and Self-TestsEngaging SELF-TESTS ActivMedia Robotics Operating System CLIENT-SERVER Communication Packet ProtocolsPacket Errors Packet ChecksumServer Information Packets Multiply by DistConvFactor‡Client Commands Before Client ConnectionP2OS CLIENT-SERVER Connection Keeping the Beat-PULSE Autoconfiguration SYNC2Opening the Servers-OPEN Closing the Connection-CLOSEMotion Commands RotationActivMedia Robots in Motion Platform Dependent and Independent VariablesPID Controls Internal coordinate systemSonar Enable/Disabling SonarPosition Integration Polling Sequence and RateStalls and Emergencies 11-15 ReservedAccessory Commands and Packets Packet ProcessingChanging Baud Rates and Autobauding CONFIGpac and Config CommandSerial Port Communications Gripper packets HOST-to-AUX Serial TransfersEncoder Packets Sounds TCM2Onboard PC Heading Correction GyroInput Output I/O User I/OBumper and IR I/O IO packetsDigital Port Controls Expansion I/ODOCKING/CHARGING System I/O Docking/Charging ServersMonitoring the Recharge Cycle Charge State Overcharge ~Volts Charge current ID7ActivMedia Robotics Operating System Aros Maintenance Mode Updating & Reconfiguring ArosWhere to GET Aros Software Simple Aros UpdatesUpdating and Reconfiguring Aros Starting AroscfChanging Parameters Configuring Aros Operating ParametersInteractive Commands Save Your Work PID ParametersKeyword Ticksmm and Revcount 0056 0057 0060 0034Stallval and Stallcount BumpersUpdating and Reconfiguring Aros Drive Lubrication Maintenance & RepairTire Inflation BatteriesTightening the AT Drive Belt Alternative Battery ChargersAutomated Docking/Charging System Getting Inside Removing the NoseOpening the Deck Factory RepairsH8S Ports & Connections Power ConnectorAppendix a H8S MicrocontrollerSerial Ports User I/O, Gripper, Docking/Charging PortOD7 Expansion I/O BusUser Control Interface Bumper PortsMotors, Encoders, and IR Sensors Joystick Port Appendix B Pioneer 3 and 2-PLUS MOTOR-POWER BoardConfiguration for Current and Temperature Sensing Controller Power and Interface Radio, Auxiliary, and User Power ConnectorsIR Signal and Power GNDRadio Modem Settings Appendix CAppendix D Serial Ethernet SettingsConsole mode Webpage Peer-to-Peer NetworkingSpecifications Appendix EControls and Ports Warranty & Liabilities Columbia Drive Amherst, NH 603