Agilent Technologies 82350B manual System

Page 38

1 Installing and Configuring the 82350

Table 1-182350 GPIB interface card configuration parameters

VISA

Symbolic name that VISA uses to uniquely identify this GPIB

Interface ID

interface. The default VISA interface ID is GPIB0. The 82350

 

interface ID for VISA must begin with the string GPIB and

 

have an integer appended to it, such as GPIB0, GPIB1,

 

GPIB2, etc. Remember this value to properly address GPIB

 

devices in your VISA applications.

 

 

GPIB

Address of this GPIB interface controller on the GPIB bus. It

Address

is usually 21 if the GPIB interface is a System Controller or

 

20 if the GPIB interface is a non-System Controller (see

 

System Controller, following). These addresses are chosen

 

by convention but any address in the range 0 - 30, inclusive,

 

may be used.

 

 

System

Determines if this interface controls which bus devices talk

Controller

and which bus devices listen. If several devices exist on a

 

bus, be sure each has a unique GPIB bus address and only

 

one device is the System Controller. Each GPIB interface has

 

its own independent bus. Thus, each interface may be a

 

System Controller as long as it is not chained together with

 

other GPIB interfaces. However, two or more System

 

Controllers on the same bus will cause the bus to be

 

inoperative.

 

 

SICL

Symbolic name that SICL uses to uniquely identify this GPIB

Interface ID

interface. The default Interface ID is gpib0. The SICL

 

interface ID must be a unique string of alphanumeric

 

characters, starting with a letter. Remember this value and

 

the logical unit number to properly address GPIB devices in

 

your SICL applications.

 

 

Logical Unit

Number that SICL uses to uniquely identify this 82350

 

interface. The logical unit number is an integer in the range

 

of 0 - 10000. Remember this value and the SICL interface ID

 

to properly address the GPIB interface in your SICL

 

applications.

 

 

26

82350B Installation and Configuration Guide

Image 38
Contents PCI Gpib Manual Part Number Safety Notices Safety Symbols Page General Safety Information Environment Conditions Regulatory Markings Page Declaration of Conformity Contents Specifications and Information Installing and Configuring Getting Started 182350B system overviewBefore you install Check your shipmentWindows XP Service Pack 3 or later System requirements1Ghz 32- bit x86, 1GHz 64- bit x64, no support for Itanium64 Create an emergency repair disk Installing the Agilent IO Libraries Suite Checking for installed Agilent IO LibrariesInstalling and Configuring Installing Agilent IO Libraries Suite Click Start Run Installing and Configuring the 82350 If you accept the Typical Installation, click Next and pro Installing and Configuring the 82350 When you are done selecting features, click Next Installing and Configuring the 82350 T E Connecting your instruments Installing the 82350 in your PC4Remove the PC cover Connecting instruments to Installing and Configuring 8Connecting a single Gpib instrument Example Connecting Multiple Gpib Instruments Configuring Installing configuration filesConfiguring the 82350 interface 10Agilent Connection Experts11Configure Gpib card parameters System Installing and Configuring the 82350 Communicating with your instruments Verifying instrument communicationProgramming your instruments 12Agilent Interactive IOAccessing Programming Manuals and Help Example Gpib Interface Configuration 13Interface configuration for multiple instruments Troubleshooting Guidelines Troubleshooting Overview 1Troubleshooting overviewCheck cables/connections/power Hardware ChecksCheck Device Manager Number ffffffff Troubleshooting Guidelines 82350B Installation and Configuration Guide Disable Connection Expert Auto-Discovery Software Checks82350B Installation and Configuration Guide Set 82350 Read/Write Performance Mode 82350B Installation and Configuration Guide Troubleshooting Guidelines Check IO Libraries Suite installation Agilent IO Libraries Suite ChecksCheck IO Control operation Install IO Libraries Suite if 82350 was installed first Windows XP/Vista/7 Specifications Information General Requirements General Characteristics +5V PCIAccessing an Electronic Copy of this Guide Contacting Agilent URLSpecifications and Information Index GpibWeb sites, Agilent Contact us