Motorola XTNI manual Frequencies

Page 37

 

1

 

 

Frequencies

 

 

First

PTT

Second

PTT

Digit

 

Digit

 

Reading CTCSS/DPL Values

If you continue short pressing the PTT button, as shown in the ”Entering Programming Mode” on page 33 (Stage 2) the radio will move forward to programming CTCSS/PL Codes. When reading the values for CTCSS/PL Codes the radio signals you the digit codes each time you short press the PTT button. You will have to read three digits as XTNi Series™ have up to 122 codes available (refer to ‘Frequencies and Codes Charts’ Section).

The following is an example of the order in which your radio will be signaling the ‘118’ CTCSS/DPL code:

:

1

1

8

 

 

 

First

 

 

Third

 

 

Digit

 

 

Digit

 

 

Second Digit

 

 

 

Example of how to program values

 

 

 

 

 

 

• Short press the PTT button. The radio will

 

signal you the first digit ‘1’, short press PTT

 

button again and the radio will show the

PROGRAMMING FEATURES

second digit ‘1’ and finally, short press PTT

 

again and radio will show the third digit ‘8’.

 

 

 

35

 

 

 

 

 

 

 

 

 

 

English

 

 

 

 

 

 

 

 

 

 

 

Page 36 Page 38
Image 37
Page 36 Page 38
Contents Page Page Contents Hands Free without Accessories iVOX30 Contents AccessoriesComputer Software Copyrights Computer Software CopyrightsSafety SafetyBatteries and Chargers Safety Information Batteries and Chargers Safety InformationOperational Safety Guidelines Parts of the Radio Radio OverviewRadio Overview Overview RadioModel Frequency Transmit Power Number Antenna Band About the Li-Ion Battery Battery Features and Charging OptionsBatteries and Chargers Batteries and Chargers Battery Recycling and DisposalBattery Latchbattery latch Slots Turn OFF the radio, if it is turned on Removing Alkaline BatteriesPower Supply, Adaptors and Drop-in Tray Charger Battery Life Information Installing Spring Action Belt ClipCharging with the Drop-in Tray Single Unit Charger Charging the BatteryCharging a Stand-alone Battery Adjustable bracket Standard High and Ultra High Capacity Charging a High Capacity Battery Standard Charger LED Indicator Drop-in Tray Charger LED IndicatorsEstimated Charging Time Status LED Status Comments Getting Started Talk Range Receiving a CallGetting Started Radio Status LED Indication Radio LED IndicatorsHANDS-FREE USE/VOX Getting Started With Compatible VOX AccessoriesSetting VOX Sensitivity Hands Free without Accessories iVOXBattery Save Microphone GainEnd of Transmission Tone Roger Beep Tone Reset To Factory DefaultsProgramming Mode Programming FeaturesLearning To Read The Values The Radio Signals You Features Programming Mode Reading your Radios Features ValuesProgramming Features Programming ModeReading Frequencies Values Entering Programming ModeFrequencies Reading Auto-Scan Values Saving SettingsProgramming Frequencies, Codes and Auto-Scan Programming Mode FAQ Just programmed the value I wanted Example of Programming a Code Example of Programming Auto Scan Other Programming Features ScanNuisance Channel Delete Editing Scan ListCPS Computer Programming Software Battery Type Setting Time-Out TimerBandwidth Select Call TonesCloning with a Multi-Unit Charger MUC Programming Features Cloning RadiosPress and release SB1 When ordering the MUCOperating Instructions What to do if cloning fails Cloning using the CPS Computer Programming SoftwareTroubleshooting TroubleshootingMonitoring’ Section on page 24 for further information Light does not come on If the radio is submerged in water USE and CareUSE and Care Frequency and Code Charts Frequency and Code ChartsChannel Radios PMR 446 Defaults Ctcss CtcssDPL Codes DPL Code Warranty Information WarrantyWhat is not Covered by the Warranty Motorola LimitedMotorola Limited Warranty Accessories Chargers Page 6871663M06-A
Top Page Image Contents