Abocom None user manual Lowest, Authentication and Security tab

Page 17

•The Ad-hoclets users set a small wireless workgroup easily and quickly. Equipped with the Wireless LAN USB Adapter, users can share files and printers between each PC and laptop.

Tx Power: Transmit power, the amount of power used by a radio transceiver to send the signal out. Select the Tx power percentage from the pull-down list including Auto, 100%, 75%, 50%, 25%, 10% and

Lowest.

Preamble: This function will show up when Ad-hoc network type be selected. A preamble is a signal used in wireless environment to synchronize the transmitting timing including Synchronization and Start frame delimiter. Select from the pull-down menu to change the Preamble type into Auto or Long.

Power Save Mode:

•CAM (Constantly Awake Mode): When this mode is selected, the power supply will be normally provided even when there is no throughput. (Default power save mode is CAM.)

•PSM (Power Saving Mode): When this mode is selected, this device will stay in power saving mode even when there is high volume of throughput.

RTS Threshold: Users can adjust the RTS threshold number by sliding the bar or key in the value directly. (The default value is 2347.) RTS/CTS Threshold is a mechanism implemented to prevent the “Hidden Node” problem. If the “Hidden Node” problem is an issue, users have to specify the packet size. The RTS/CTS mechanism will be activated if the data size exceeds the values that have been set.

This value should remain at its default setting of 2347. Should users encounter inconsistent data flow, only minor modifications of this value are recommended.

Fragment Threshold: Users can adjust the Fragment threshold number by sliding the bar or key in the value directly. (The default value is 2346.) The mechanism of Fragmentation Threshold is used to improve the efficiency when high traffic flows along in the wireless network. If the Wireless LAN USB Adapter often transmits large files in wireless network, users can enter new Fragment Threshold value to split the packet. The value can be set from 256 to 2346.

Authentication and Security tab:

Authentication Type: There are several types of authentication modes including Open, Shared, Leap, WPA, WPA-PSK, WPA2 and WPA2-PSK.

•Open: If the access point or wireless router is using "Open” authentication, then the Wireless LAN USB Adapter will need to be set to the same authentication type.

-13 -

Page 16 Page 18
Image 17
Page 16 Page 18
Contents 802.11 b/g/n Mini Wireless LAN USB 2.0 Adapter Country Code Statement Federal Communication Commission Interference StatementTable of Contents Uninstallation For Windows 2000/XP For Windows Vista Chapter Introduction FeaturesInstall the Software Chapter InstallationPage Install the Hardware Verification For Windows Vista Page Install the Hardware IP Address Network Connection Utility Configuration Network Type Authentication Station ModeProfile Profile TabSystem Configuration tab Lowest Authentication and Security tab802.1x tab ID\PASSWORD tab Tunnel AuthenticationEAP Method EAP-MSCHAP v2, EAP-TLS/ Smart Card, and Generic Token CardServer Certification tab Client Certification tabNetwork Tab NetworkGeneral Access Point AP Information802.11n Link StatusLink Status Tab Advanced Tab AdvancedTransmit StatisticsReceive Statistics WMM/ QoSDirect Link Setup Enable WMM Enable WMM- Power Save EnableMAC Address Timeout Value Apply Tear Down WMM/QoS TabWPS Tab WPS AP List Rescan Information PIN Code Config Mode DetailConnect Rotate Disconnect Export Profile Radio On/OffDelete WPS Associate IE WPS Probe IE Auto Progress Bar Status BarAbout Utility Menu ListConfig Soft AP modeConfig Channel Wireless Mode Use Mac Address Security SettingBeacon ms TX Power Idle time60-3600s Access Control MAC Table Access ControlEvent Log Power Saving Mode StatusMAC Table Event LogTransmit Statistics About Launch Config Utility Network Type Authentication Encryption Use Tx Power Channel Power Save Mode RTS Threshold Fragment Threshold Add Authentication and Encryption tab 802.1x tab EAP Method Tunnel Authentication Network Add to Profile WPS CCX Link Status Advanced Enable TCP Window Size Fast Roaming at Apply Wireless mode Enable TX BurstReceive Statistics Tab Reset Counter Click this button to reset counters to zeroTransmit Statistics Tab WMM Enable WPS AP List Config Mode Detail Connect WPS Probe IE Progress Bar Status Bar Rotate DisconnectWPS Associate IE Radio On/Off Utility Menu List Soft AP mode Beacon ms TX Power Idle time60-3600s Clients Hide Ssid Among wirelessNo forwarding Display all MAC Address that users have set Event Log Statistics About Uninstallation Page For Windows Vista Finally, click Finish to complete the uninstallation
Top Page Image Contents