3Com 10/100BASE-T4 PCI manual CONFIG\3C595.SET

Page 54

Changing Software Settings

B-5

You must highlight OK and press [Enter] to save the settings. If you want to use the same settings on other adapters, you can save the configuration settings to a file. Select Save under File Options in the Adapter Configuration dialog box. For example, type:

D:\CONFIG\3C595.SET

This saves the settings to the default file 3C595.SET in the CONFIG directory in drive D. Refer to the on-line help (press [F1]) for more information.

Page 53 Page 55
Image 54
Page 53 Page 55
Contents User Guide Fast Etherlink Parallel TaskingNetwork Adapter Adapters3Com Corporation 5400 Bayfront Plaza Santa Clara, California Lifetime Warranty Asia Contents Configuring Software Settings Cispr B Compliance Figures Tables How to Use This Guide About this GuideIntroduction Conventions Print Autolink.logAdapter automatically senses and switches to either Introduction10/100BASE-T4 PCI Adapter Adapter Features PCI Technology Installing the Adapter Inspecting the Adapter3C59X EtherDisk diskette version 5.1 or above Installing the Boot Prom Installing the AdapterConnecting to the Network PCI Computer with PCI and Eisa SlotsRJ-45 connector Connecting to the Network Summary of Driver Loading Procedures Loading the NetworkDrivers Using the EtherDisk Diskette Accessing DOSUsing Windows Name of the installed 3Com adapter appears, as follows Confirming Adapter Installation for WindowsSystem Properties box appears, detailing your system setup This confirms the adapter’s installationUsing NetWare ODI One Adapter in a ClientAutoLink Requirements AutoLink Installation At the prompt, typeAlternatively, at the prompt, type ESC=Cancel Read the screen and press EnterMultiple Adapters in a Client FEA0 Select Configuration and Diagnostic Program and press Enter Main menu appearsLoading Ndis Drivers One or More Adapters in a ServerUpdating Ndis Drivers Auto Select Media TypeFollow the instructions displayed in the subsequent screens Transcend PC Link SmartAgent Driver Agents Desktop Management InterfacePerforming Troubleshooting Diagnostic Tests Troubleshooting with the Diagnostic TestsTypes of Tests After performing the diagnostic tests, reboot your computerBefore Running the Tests Fast EtherLink 10/100BASE-T4 PCI adapterStarting the Diagnostic Program Running the Group 1 TestsRunning the Group 3 Test Setting Up an Echo Server 3C59XCFG Getting Help If a Test Fails To print the file, type Changing the Test Setup Miscellaneous ChecksTo change the test parameters, follow these steps LEDs LEDCabling Pin assignments for the RJ-45 connectorWhen properly connected to a 10BASE-T network, Adapter Cabling RequirementsTwisted-Pair Cable 10BASE-T Operation 10BASE-T Specifications100BASE-T Standard 100BASE-TX Operation100BASE-TX designates the Ieee 802.3 specification for 100BASE-T4 Operation 100BASE-FX OperationRJ-45 Connector Pin Assignments Figure A-1 shows the RJ-45 connector pin assignmentsSettings Changing Software Settings To change the software option settings, follow these stepsType at the prompt Select Adapter Installed Adapters Continue this procedure with any of the other options Press Tab to highlight OK. Press Enter\CONFIG\3C595.SET Specifications Adapter SpecificationsOn-line Technical Services 3Com Bulletin Board ServiceTechnical Support To use 3ComForum Log on to CompuServe World Wide Web Site3ComForum on CompuServe Press Return to see the 3ComForum main menu3ComFacts Automated Fax Service Support from Your Network SupplierLocal numbers are available within the following countries Returning Products for Repair Details about recent configuration changes, if applicableTo obtain an RMA number, call or fax Glossary 100BASE-TAuto Select Media Type BusEIA/TIA EMM386MAC STP Index NumericsDOS Ndis Network Driver Optimization option setting B-2 Windows 3.X 3-3 Windows Limited Warranty 3Com Corporation Bayfront Plaza Interference Handbook CE Notice
Top Page Image Contents