3Com 10/100BASE-T4 PCI manual Figures

Page 8

FIGURES

1-1

10/100BASE-T4 PCI Adapter

1-2

 

2-1

PCI Computer with PCI and EISA Slots

2-3

2-2

Connecting Twisted-Pair Cable 2-4

 

3-1

AutoLink Information Screen

3-7

 

3-2

Main Menu 3-7

 

 

A-1

RJ-45 Connector Pin Assignments A-6

 

B-1

Multiple Adapter Option Configuration

B-3

B-2

Changing Adapter Options

B-4

 

Image 8
Contents Fast Etherlink Parallel Tasking Network AdapterUser Guide Adapters3Com Corporation 5400 Bayfront Plaza Santa Clara, California Lifetime Warranty Asia Contents Configuring Software Settings Cispr B Compliance Figures Tables Introduction How to Use This GuideAbout this Guide Conventions Print Autolink.logAdapter automatically senses and switches to either Introduction10/100BASE-T4 PCI Adapter Adapter Features PCI Technology 3C59X EtherDisk diskette version 5.1 or above Installing the AdapterInspecting the Adapter Installing the Boot Prom Installing the AdapterConnecting to the Network PCI Computer with PCI and Eisa SlotsRJ-45 connector Connecting to the Network Drivers Summary of Driver Loading ProceduresLoading the Network Using the EtherDisk Diskette Accessing DOSUsing Windows Confirming Adapter Installation for Windows System Properties box appears, detailing your system setupName of the installed 3Com adapter appears, as follows This confirms the adapter’s installationAutoLink Requirements Using NetWare ODIOne Adapter in a Client Alternatively, at the prompt, type AutoLink InstallationAt the prompt, type ESC=Cancel Read the screen and press EnterMultiple Adapters in a Client FEA0 Select Configuration and Diagnostic Program and press Enter Main menu appearsLoading Ndis Drivers One or More Adapters in a ServerFollow the instructions displayed in the subsequent screens Updating Ndis DriversAuto Select Media Type Transcend PC Link SmartAgent Driver Agents Desktop Management InterfacePerforming Troubleshooting Diagnostic Tests Troubleshooting with the Diagnostic TestsAfter performing the diagnostic tests, reboot your computer Before Running the TestsTypes of Tests Fast EtherLink 10/100BASE-T4 PCI adapterStarting the Diagnostic Program Running the Group 1 TestsRunning the Group 3 Test Setting Up an Echo Server 3C59XCFG Getting Help If a Test Fails To print the file, type To change the test parameters, follow these steps Changing the Test SetupMiscellaneous Checks LEDs LEDPin assignments for the RJ-45 connector When properly connected to a 10BASE-T network,Cabling Adapter Cabling RequirementsTwisted-Pair Cable 10BASE-T Operation 10BASE-T Specifications100BASE-TX designates the Ieee 802.3 specification for 100BASE-T Standard100BASE-TX Operation 100BASE-T4 Operation 100BASE-FX OperationRJ-45 Connector Pin Assignments Figure A-1 shows the RJ-45 connector pin assignmentsSettings Type at the prompt Changing Software SettingsTo change the software option settings, follow these steps Select Adapter Installed Adapters Continue this procedure with any of the other options Press Tab to highlight OK. Press Enter\CONFIG\3C595.SET Specifications Adapter SpecificationsTechnical Support On-line Technical Services3Com Bulletin Board Service World Wide Web Site 3ComForum on CompuServeTo use 3ComForum Log on to CompuServe Press Return to see the 3ComForum main menuLocal numbers are available within the following countries 3ComFacts Automated Fax ServiceSupport from Your Network Supplier To obtain an RMA number, call or fax Returning Products for RepairDetails about recent configuration changes, if applicable Glossary 100BASE-TAuto Select Media Type BusEIA/TIA EMM386MAC STP Index NumericsDOS Ndis Network Driver Optimization option setting B-2 Windows 3.X 3-3 Windows Limited Warranty 3Com Corporation Bayfront Plaza Interference Handbook CE Notice