3Com 10/100BASE-T4 PCI manual Performing Troubleshooting Diagnostic Tests

Page 34

PERFORMING

4 TROUBLESHOOTING AND

DIAGNOSTIC TESTS

This chapter explains how to isolate and solve 10/100BASE-T4 PCI adapter problems.

Make sure that the adapter is correctly installed. (See Chapter 2 for installation instructions.)

This chapter contains information about the following topics:

■Diagnostic tests overview

■Starting the diagnostic program

■Getting help if a test fails

■Changing the test setup

■Miscellaneous checks

The 3Com diagnostic program is a DOS program. If you are running an operating system or interface other than DOS, refer to the section “Accessing DOS” in Chapter 3.

Troubleshooting with the Diagnostic Tests

The diagnostic tests on the 3C59X EtherDisk diskette check the adapter’s overall operation and permit the isolation of faults. You can run the diagnostic tests after installing the 10/100BASE-T4 PCI adapter, or when a fault is suspected.

If the tests in their default conﬁguration do not isolate the problem, you can change the test parameters to meet speciﬁc situations.

Image 34

Contents User Guide Fast Etherlink Parallel TaskingNetwork Adapter Adapters3Com Corporation 5400 Bayfront Plaza Santa Clara, California Lifetime Warranty Asia Contents Configuring Software Settings Cispr B Compliance Figures Tables About this Guide How to Use This GuideIntroduction Conventions Print Autolink.logAdapter automatically senses and switches to either Introduction10/100BASE-T4 PCI Adapter Adapter Features PCI Technology Inspecting the Adapter Installing the Adapter3C59X EtherDisk diskette version 5.1 or above Installing the Boot Prom Installing the AdapterConnecting to the Network PCI Computer with PCI and Eisa SlotsRJ-45 connector Connecting to the Network Loading the Network Summary of Driver Loading ProceduresDrivers Using the EtherDisk Diskette Accessing DOSUsing Windows Name of the installed 3Com adapter appears, as follows Conﬁrming Adapter Installation for WindowsSystem Properties box appears, detailing your system setup This conﬁrms the adapter’s installationOne Adapter in a Client Using NetWare ODIAutoLink Requirements At the prompt, type AutoLink InstallationAlternatively, at the prompt, type ESC=Cancel Read the screen and press EnterMultiple Adapters in a Client FEA0 Select Conﬁguration and Diagnostic Program and press Enter Main menu appearsLoading Ndis Drivers One or More Adapters in a ServerAuto Select Media Type Updating Ndis DriversFollow the instructions displayed in the subsequent screens Transcend PC Link SmartAgent Driver Agents Desktop Management InterfacePerforming Troubleshooting Diagnostic Tests Troubleshooting with the Diagnostic TestsTypes of Tests After performing the diagnostic tests, reboot your computerBefore Running the Tests Fast EtherLink 10/100BASE-T4 PCI adapterStarting the Diagnostic Program Running the Group 1 TestsRunning the Group 3 Test Setting Up an Echo Server 3C59XCFG Getting Help If a Test Fails To print the ﬁle, type Miscellaneous Checks Changing the Test SetupTo change the test parameters, follow these steps LEDs LEDCabling Pin assignments for the RJ-45 connectorWhen properly connected to a 10BASE-T network, Adapter Cabling RequirementsTwisted-Pair Cable 10BASE-T Operation 10BASE-T Speciﬁcations100BASE-TX Operation 100BASE-T Standard100BASE-TX designates the Ieee 802.3 speciﬁcation for 100BASE-T4 Operation 100BASE-FX OperationRJ-45 Connector Pin Assignments Figure A-1 shows the RJ-45 connector pin assignmentsSettings To change the software option settings, follow these steps Changing Software SettingsType at the prompt Select Adapter Installed Adapters Continue this procedure with any of the other options Press Tab to highlight OK. Press Enter\CONFIG\3C595.SET Specifications Adapter Speciﬁcations3Com Bulletin Board Service On-line Technical ServicesTechnical Support To use 3ComForum Log on to CompuServe World Wide Web Site3ComForum on CompuServe Press Return to see the 3ComForum main menuSupport from Your Network Supplier 3ComFacts Automated Fax ServiceLocal numbers are available within the following countries Details about recent conﬁguration changes, if applicable Returning Products for RepairTo obtain an RMA number, call or fax Glossary 100BASE-TAuto Select Media Type BusEIA/TIA EMM386MAC STP Index NumericsDOS Ndis Network Driver Optimization option setting B-2 Windows 3.X 3-3 Windows Limited Warranty 3Com Corporation Bayfront Plaza Interference Handbook CE Notice