AMX manual MAX-CSE and MAX-CSD10 Installation, MAX-CSE and MAX-CSD10 Connections and Wiring

Page 15

MAX-CSE and MAX-CSD10 Installation

MAX-CSE and MAX-CSD10 Installation

MAX-CSE and MAX-CSD10 Connections and Wiring

The MAX CSE and MAX-CSD10 are configured to be used as standalone units running on a network capable of supporting the up to a 6Mbps data rate. It is recommended that you set up the unit locally prior to installing it within an AC-RK 19-inch rack unit, as described on page 17.

Port Assignments and Functionality

The rear Port Assignments are as follows:

MAX-CSE Port Assignments

Description

ICSP Port #

 

 

Video Encoder

1

 

 

RS-232/422/485 (DB9) Serial Port

2

 

 

IR/Serial Port

3

 

 

I/O Port

4

 

 

IR RX Port

5

 

 

LCD Display

6

 

 

MAX-CSD10 Port Assignments

Description

ICSP Port #

 

 

Video Decoder

1

 

 

RS-232/422/485 (DB9) Serial Port

2

 

 

IR/Serial Port

3

 

 

I/O Port

4

 

 

IR RX Port

5

 

 

LCD Display

6

 

 

Wiring Guidelines - Direct Power

The MAX-CSE and MAX-CSD10 units require the use of either an external 12 VDC-compliant power supply or an 802.3af-compliant device to provide DC power. Power can be fed to the unit through either the rear 2-pin 3.5mm mini-Phoenix PWR connector or the rear Ethernet connector (PoE).

Use the power requirements from the Specifications table on page 2 to determine the unit’s power draw.

This unit should only have one source of incoming power. Although the unit can be connected to two separate power sources, the

12 VDC-compliant power input overrides the PoE. Refer to the Wiring Guidelines - Indirect Power (via PoE) section on page 10 for specific PoE wiring procedures and restrictions.

MAX-CSE/MAX-CSD10 Operation/Reference Guide

9

 

 

Image 15
Contents MAX-CSE/MAX-CSD10 AMX Limited Warranty and Disclaimer Table of Contents MAX-CSD10 Web Interface Displaying Stream Content Page MAX Encoder Features MAX-CSE Video EncoderOverview MAX-CSE Specifications MAX-CSE Product SpecificationsWhile in IR mode Sensing for IR ports MAX-CSD10 FG2178-72 MAX-CSD10 Product SpecificationsMAX Decoder Features MAX-CSD10 Video DecoderAAC MAX-CSD10 FG2178-72 SpecificationsComposite OUT MAX-CSD10 SpecificationsPage Port Assignments and Functionality MAX-CSE and MAX-CSD10 InstallationMAX-CSE and MAX-CSD10 Connections and Wiring Wiring Guidelines Direct PowerWiring Guidelines Indirect Power via PoE Wiring Length GuidelinesPreparing Captive Wires Wiring a Power ConnectionMAX-CSE PoE Special Wiring InstructionsVDC power Supply Wiring the MAX-CSE Connectors and CablesMIC Ethernet/RJ-45 Port Connections and WiringEthernet RJ-45 Pinouts and Signals Signals Connection Pairing ColorPower over Ethernet PoE Wiring DB9 Device Port Connections and WiringEthernet LEDs IR/Serial Port Connections and Wiring Input/Output I/O Port Connections and WiringRS-232/422/485 Device Port Wiring Specifications Wiring the MAX-CSD10 Connectors and Cables Port Wiring SpecificationsPin Signal Function Installing Into an Equipment Rack Page Security Terms Default Security ConfigurationMAX-CSE Web Interface Security TermsDefault Security Configuration case-sensitive Administrator accountCommunicating with the Unit via the Browser-Based UI Browser-based UI Application Overview MAX-CSE User Interface Overview and FeaturesUser Interface Features Feature Description Navigation BarAdministration Page Features Feature DescriptionStream Status Example Computer Course AdministrationAdministration Feature Description ResourcesChanging the Program Description ModeUpload Firmware Upgrading New Firmware Click Upload a File Click Reboot done. Upload a FileStream Profiles Stream ProfilesStream Profiles Page Features Feature Description Encoder ProfileVideo Audio 30fps for Ntsc and 352x288 @ 24 fps for PALStream SVCD, MP3Obtaining the IP information for a target Modero SAP SettingsVCR Encoder Profiles and ParametersChanging the Encoder Profile Set-upChanging Video and Audio Settings Set up Page FeaturesFeature Description Video NetLinx Settings NetLinx SettingsFeature Description NetLinx Master NetLinx Settings Page FeaturesChanging the NetLinx Master Connection IP Settings IP SettingsDNS Address Changing the IP SettingsIP Settings Page Features Feature Description IP AddressUser Page Features Feature Description UserUser Changing User Settings Navigation frame MAX-CSD10 User Interface Overview and FeaturesFeature Description Browser Address field MAX-CSD10 Web InterfaceFeature Description Stream Status frame LogoffActive Page frame Updating Firmware Communicating with the Unit via the Browser-based UIStream Selector Stream Selector Page FeaturesStream Set-up Stream Set-Up Page FeaturesChanging the Stream Configuration Setting up an SAP Stream ConfigurationSetting up an Rtsp Stream Configuration Stream Configuration Page Manual Mode Setting up a Manual Stream ConfigurationNetLinx Audio/Video Page FeaturesNetLinx Page Features Audio/VideoSelects whether the IP access is dynamic or static User Page Details To change the User Login SettingsReading the Front Panel LCD Configuring CommunicationObtaining the Unit’s Initial Dhcp Address Configuring the MAX Communication ParametersSave login profile selection box Configuring Communication NetLinx Studio NetLinx Studio Communicating with the Target Master via an IPConfiguring Communication Associating a MAX-CSE to a Target Master Associating the MAX Unit to a Target MasterStudio Online Tree tab showing the communicating MAX unit Changing the MAX-CSE Device Number via Studio Changing the MAX’s Device NumberAssociating a MAX-CSD10 Unit to a Target Master Changing the MAX-CSE Device Number via the UIRecommended NetLinx Device Numbers Using the ID Button to Change the MAX-CSE’s Device ValueChanging the MAX-CSD10 Device Number via the UI Page Verifying the MAX’s Current Version of Firmware via the UI Configuration and Firmware UpdateBefore You Begin MAX vs. NetLinx Master Functional OverlapUpgrading MAX Firmware Verifying the MAX’s Current Version of Firmware via StudioUpgrading MAX-CSE Firmware via the UI Upgrading the MAX’s Firmware via NetLinx Studio Upgrading MAX-CSD10 Firmware via the UIClick Close once the download process is complete Requirements for Receiving Streamed Content Displaying Stream ContentObtaining the IP Address of the Target Panel Setting up a Modero Panel to Receive and Display a StreamSystem Settings Configuring the MAX-CSE for communicationStream Profiles Displaying Stream Content V Setup Configuring the MAX-CSE Audio/Video InputsButton Properties tab Setting up a streaming page within TPDesign4Rtpmpeg#//IP Address of MAX-CSETarget Video Port Establishing the Final Connection Between the Two Units Video Adjustment page showing default valuesSetting up a Computer to Receive and Display a Stream Configure the MAX-CSE for Communication to a ComputerObtaining the IP Address of the Target Computer Displaying Stream Content RTP Video Stream Component RTP Audio Stream Component Port/Description NetLinx ProgrammingDevicePortSystem DPS Port AssignmentsGET Asource MAX-CSE Streaming Commands PortMAX-CSE Streaming SendCommands Command DescriptionGET SAP GET SAP IP ModeGET Format GET GainGET Session Info GET Session ListGET Stream Status GET URL GET VideoGET Video Port Status SET Audio GET VsourcePlay SET AsourceSET SAP SET SAP IP ModeSET Format SET GainSendcommand ENCODER,SET Video MPEG2 D1 6000 CBR SET URLSET Video SET Vsource Sendcommand ENCODER,SET Vsource SvidSendcommand DEV,STOP Sendcommand ENCODER,STOPMAX-CSD10 Streaming Commands Port MAX-CSD10 Streaming SendCommandsGET Control Mode GET Rtsp Server GET Session Cursor GET Session ChangeSendcommand DECODER,GET Stream Status Sendcommand DEV,GET Session ListSendcommand DECODER,GET Session List Sendcommand DEV,GET Stream StatusSET Control Mode SET Rtsp Server Sendcommand DECODER,SET SAP IP Mode ALTSendcommand DECODER,SET SAP IP ALT Sendcommand DECODER,SET Session CursorSendcommand DECODER,SET Video MPEG2 D1 Sendcommand DECODER,START Rtsp ServerStart Rtsp Server RS-232/422/485 SendCommands RS-232/422/485 SendCommands PortRxclr GET BaudHsoff HsonXoff SET BaudTset Baud TxclrRS-232/422/485 SendString Escape Sequences RS232/422/485 Ports ChannelsRS-232/422/485 SendString Escape Sequences Port RS232/422/485 Ports Channels27,20,0 Command Description 27,19,timeIR / Serial Ports Channels IR / Serial Ports ChannelsCaron IR/Serial Port Port 3 CommandsIR/Serial SendCommands CaroffIroff GET ModeCtof CtonPOD POFPON Ptof PtonSET IO Link Short cable length 10 feet SET ModeSendcommand IR1,SET Mode IR Sendcommand IR1, SP,25Xchm Sendcommand DEV,XCHM extended channel modeSendcommand IR1,XCHM Sendcommand IR1,XCHGET Input Port Commands PortSend Commands IR RX Port Channels PortBACKLIGHT-50 LCD Commands PortBacklight BACKLIGHT-0Page Programming MAX-CSE/MAX-CSD10 Operation/Reference Guide 109 It’s Your World Take Control
Related manuals
Manual 2 pages 30.49 Kb Manual 110 pages 20.97 Kb Manual 2 pages 62.62 Kb

MAX-CSD10, MAX-CSE specifications

The AMX MAX-CSE and MAX-CSD 10 are advanced multimedia presentation systems designed to enhance communication and collaboration in various professional environments. These devices are tailored for modern conference rooms, educational institutions, and corporate settings, providing seamless integration of audio-visual technology to facilitate effective presentations and meetings.

One of the standout features of the MAX-CSE and MAX-CSD 10 is their sophisticated audio and video processing capabilities. The MAX-CSE serves as a central management hub, supporting high-definition video outputs and multiple input sources, including HDMI, VGA, and wireless connectivity options. This versatility ensures that users can connect a wide array of devices—laptops, tablets, and smartphones—without hassle and quickly switch between them during presentations.

The MAX-CSD 10 complements the MAX-CSE as a dedicated audio unit equipped with powerful amplification and precise tuning. It delivers clear and balanced sound, even in larger rooms, ensuring that every participant can engage fully, regardless of their location in the space. With features like echo cancellation and noise reduction technology, the MAX-CSD 10 enhances voice clarity, making it ideal for video conferencing and webinars.

An important characteristic of the AMX MAX series is their user-friendly interface. The systems are designed for intuitive operation, enabling users to control various settings with ease, whether they are tech-savvy or not. The touch panel interface can be customized to meet specific needs, allowing quick access to essential functions such as lighting, video routing, and audio control.

In terms of connectivity, both systems are equipped with robust network capability, allowing integration with existing IT infrastructure. This feature ensures that users can manage and control the systems remotely through a web interface or compatible applications, enhancing productivity and easing the overall user experience.

Robust security measures are also a significant aspect of the AMX MAX-CSE and MAX-CSD 10 systems. They are designed with advanced encryption and user authentication protocols, ensuring that sensitive data remains protected during presentations and meetings.

In conclusion, the AMX MAX-CSE and MAX-CSD 10 multimedia presentation systems stand out in the market due to their superior audio and video quality, user-friendly features, and extensive connectivity options. They are ideal solutions for professionals seeking to leverage technology for more productive and engaging communication.