AMX MAX-CSD10, MAX-CSE manual PoE Special Wiring Instructions, Max-Cse

Page 17

MAX-CSE and MAX-CSD10 Installation

PoE - Special Wiring Instructions

Before beginning the connection from the PoE switch to the target MAX unit, follow these instructions carefully:

When using PoE, you must FIRST ground the unit to provide ESD protection.

Refer to the procedures outlined within the previous Preparing Captive Wires section on page 10.

Install a single wire into the (-) GND side of the rear green 2-pin mini-Phoenix connector (FIG. 4).

Connect this wire to a grounded source (FIG. 4). This GND wire provides the necessary ESD protection to the unit. Only after this step has been completed can you continue on to the wiring of the PoE connection.

The length of the GND wire should not exceed 6 feet (1.83 meters).

Pre-configure the 802.3af-compliant PoE switch (such as the NXA-ENET24 PoE) and prepare it for power transmission to the target MAX unit. Refer to the PoE’s product documentation for more details.

 

 

R

 

 

 

E

 

MAX-CSE

 

A

 

 

R

 

MAX-CSE

Ethernet

 

 

 

PWR

PWR +

 

 

GND -

 

 

 

FIG. 4 ESD grounding and PoE connection of a MAX unit

802.3af-compliant

PoE switch

Grounded Metal

plate or object

Connect a CAT5/CAT6 Ethernet cable from the RJ-45 PoE connector on the PoE switch to the rear RJ-45 (Ethernet) connector on the target MAX unit (FIG. 4).

MAX-CSE/MAX-CSD10 Operation/Reference Guide

11

 

 

Image 17
Contents MAX-CSE/MAX-CSD10 AMX Limited Warranty and Disclaimer Table of Contents MAX-CSD10 Web Interface Displaying Stream Content Page Overview MAX Encoder FeaturesMAX-CSE Video Encoder MAX-CSE Specifications MAX-CSE Product SpecificationsWhile in IR mode Sensing for IR ports MAX Decoder Features MAX-CSD10 Product SpecificationsMAX-CSD10 Video Decoder MAX-CSD10 FG2178-72AAC MAX-CSD10 FG2178-72 SpecificationsComposite OUT MAX-CSD10 SpecificationsPage MAX-CSE and MAX-CSD10 Connections and Wiring MAX-CSE and MAX-CSD10 InstallationWiring Guidelines Direct Power Port Assignments and FunctionalityPreparing Captive Wires Wiring Length GuidelinesWiring a Power Connection Wiring Guidelines Indirect Power via PoEMAX-CSE PoE Special Wiring InstructionsVDC power Supply Wiring the MAX-CSE Connectors and CablesEthernet RJ-45 Pinouts and Signals Ethernet/RJ-45 Port Connections and WiringSignals Connection Pairing Color MICEthernet LEDs Power over Ethernet PoE WiringDB9 Device Port Connections and Wiring RS-232/422/485 Device Port Wiring Specifications IR/Serial Port Connections and WiringInput/Output I/O Port Connections and Wiring Pin Signal Function Wiring the MAX-CSD10 Connectors and CablesPort Wiring Specifications Installing Into an Equipment Rack Page MAX-CSE Web Interface Default Security ConfigurationSecurity Terms Security TermsCommunicating with the Unit via the Browser-Based UI Default Security Configuration case-sensitiveAdministrator account User Interface Features MAX-CSE User Interface Overview and FeaturesFeature Description Navigation Bar Browser-based UI Application OverviewStream Status Administration Page FeaturesFeature Description Administration AdministrationFeature Description Resources Example Computer CourseUpload Firmware Changing the Program DescriptionMode Upgrading New Firmware Click Upload a File Click Reboot done. Upload a FileStream Profiles Stream ProfilesVideo Stream Profiles Page FeaturesFeature Description Encoder Profile Audio 30fps for Ntsc and 352x288 @ 24 fps for PALStream SVCD, MP3Obtaining the IP information for a target Modero SAP SettingsVCR Encoder Profiles and ParametersChanging the Encoder Profile Set-upFeature Description Video Changing Video and Audio SettingsSet up Page Features NetLinx Settings NetLinx SettingsFeature Description NetLinx Master NetLinx Settings Page FeaturesChanging the NetLinx Master Connection IP Settings IP SettingsIP Settings Page Features Changing the IP SettingsFeature Description IP Address DNS AddressUser User Page FeaturesFeature Description User Changing User Settings Feature Description Browser Address field MAX-CSD10 User Interface Overview and FeaturesMAX-CSD10 Web Interface Navigation frameActive Page frame Feature Description Stream Status frameLogoff Updating Firmware Communicating with the Unit via the Browser-based UIStream Selector Stream Selector Page FeaturesStream Set-up Stream Set-Up Page FeaturesSetting up an Rtsp Stream Configuration Changing the Stream ConfigurationSetting up an SAP Stream Configuration Stream Configuration Page Manual Mode Setting up a Manual Stream ConfigurationNetLinx Page Features Audio/Video Page FeaturesAudio/Video NetLinxSelects whether the IP access is dynamic or static User Page Details To change the User Login SettingsReading the Front Panel LCD Configuring CommunicationObtaining the Unit’s Initial Dhcp Address Configuring the MAX Communication ParametersSave login profile selection box Configuring Communication NetLinx Studio NetLinx Studio Communicating with the Target Master via an IPConfiguring Communication Associating a MAX-CSE to a Target Master Associating the MAX Unit to a Target MasterStudio Online Tree tab showing the communicating MAX unit Associating a MAX-CSD10 Unit to a Target Master Changing the MAX’s Device NumberChanging the MAX-CSE Device Number via the UI Changing the MAX-CSE Device Number via StudioRecommended NetLinx Device Numbers Using the ID Button to Change the MAX-CSE’s Device ValueChanging the MAX-CSD10 Device Number via the UI Page Before You Begin Configuration and Firmware UpdateMAX vs. NetLinx Master Functional Overlap Verifying the MAX’s Current Version of Firmware via the UIUpgrading MAX-CSE Firmware via the UI Upgrading MAX FirmwareVerifying the MAX’s Current Version of Firmware via Studio Upgrading the MAX’s Firmware via NetLinx Studio Upgrading MAX-CSD10 Firmware via the UIClick Close once the download process is complete Requirements for Receiving Streamed Content Displaying Stream ContentObtaining the IP Address of the Target Panel Setting up a Modero Panel to Receive and Display a StreamSystem Settings Configuring the MAX-CSE for communicationStream Profiles Displaying Stream Content V Setup Configuring the MAX-CSE Audio/Video InputsButton Properties tab Setting up a streaming page within TPDesign4Rtpmpeg#//IP Address of MAX-CSETarget Video Port Establishing the Final Connection Between the Two Units Video Adjustment page showing default valuesObtaining the IP Address of the Target Computer Setting up a Computer to Receive and Display a StreamConfigure the MAX-CSE for Communication to a Computer Displaying Stream Content RTP Video Stream Component RTP Audio Stream Component DevicePortSystem DPS NetLinx ProgrammingPort Assignments Port/DescriptionMAX-CSE Streaming SendCommands MAX-CSE Streaming Commands PortCommand Description GET AsourceGET Format GET SAP IP ModeGET Gain GET SAPGET Stream Status GET Session InfoGET Session List GET Video Port Status GET URLGET Video Play GET VsourceSET Asource SET AudioSET Format SET SAP IP ModeSET Gain SET SAPSET Video Sendcommand ENCODER,SET Video MPEG2 D1 6000 CBRSET URL Sendcommand DEV,STOP Sendcommand ENCODER,SET Vsource SvidSendcommand ENCODER,STOP SET VsourceGET Control Mode MAX-CSD10 Streaming Commands PortMAX-CSD10 Streaming SendCommands GET Rtsp Server GET Session Cursor GET Session ChangeSendcommand DECODER,GET Session List Sendcommand DEV,GET Session ListSendcommand DEV,GET Stream Status Sendcommand DECODER,GET Stream StatusSET Control Mode Sendcommand DECODER,SET SAP IP ALT Sendcommand DECODER,SET SAP IP Mode ALTSendcommand DECODER,SET Session Cursor SET Rtsp ServerStart Rtsp Server Sendcommand DECODER,SET Video MPEG2 D1Sendcommand DECODER,START Rtsp Server RS-232/422/485 SendCommands RS-232/422/485 SendCommands PortHsoff GET BaudHson RxclrTset Baud SET BaudTxclr XoffRS-232/422/485 SendString Escape Sequences Port RS232/422/485 Ports ChannelsRS232/422/485 Ports Channels RS-232/422/485 SendString Escape SequencesIR / Serial Ports Channels Command Description 27,19,timeIR / Serial Ports Channels 27,20,0IR/Serial SendCommands IR/Serial Port Port 3 CommandsCaroff CaronCtof GET ModeCton IroffPON PODPOF SET IO Link PtofPton Sendcommand IR1,SET Mode IR SET ModeSendcommand IR1, SP,25 Short cable length 10 feetSendcommand IR1,XCHM Sendcommand DEV,XCHM extended channel modeSendcommand IR1,XCH XchmSend Commands Port Commands PortIR RX Port Channels Port GET InputBacklight LCD Commands PortBACKLIGHT-0 BACKLIGHT-50Page Programming MAX-CSE/MAX-CSD10 Operation/Reference Guide 109 It’s Your World Take Control
Related manuals
Manual 2 pages 30.49 Kb Manual 110 pages 20.97 Kb Manual 2 pages 62.62 Kb

MAX-CSD10, MAX-CSE specifications

The AMX MAX-CSE and MAX-CSD 10 are advanced multimedia presentation systems designed to enhance communication and collaboration in various professional environments. These devices are tailored for modern conference rooms, educational institutions, and corporate settings, providing seamless integration of audio-visual technology to facilitate effective presentations and meetings.

One of the standout features of the MAX-CSE and MAX-CSD 10 is their sophisticated audio and video processing capabilities. The MAX-CSE serves as a central management hub, supporting high-definition video outputs and multiple input sources, including HDMI, VGA, and wireless connectivity options. This versatility ensures that users can connect a wide array of devices—laptops, tablets, and smartphones—without hassle and quickly switch between them during presentations.

The MAX-CSD 10 complements the MAX-CSE as a dedicated audio unit equipped with powerful amplification and precise tuning. It delivers clear and balanced sound, even in larger rooms, ensuring that every participant can engage fully, regardless of their location in the space. With features like echo cancellation and noise reduction technology, the MAX-CSD 10 enhances voice clarity, making it ideal for video conferencing and webinars.

An important characteristic of the AMX MAX series is their user-friendly interface. The systems are designed for intuitive operation, enabling users to control various settings with ease, whether they are tech-savvy or not. The touch panel interface can be customized to meet specific needs, allowing quick access to essential functions such as lighting, video routing, and audio control.

In terms of connectivity, both systems are equipped with robust network capability, allowing integration with existing IT infrastructure. This feature ensures that users can manage and control the systems remotely through a web interface or compatible applications, enhancing productivity and easing the overall user experience.

Robust security measures are also a significant aspect of the AMX MAX-CSE and MAX-CSD 10 systems. They are designed with advanced encryption and user authentication protocols, ensuring that sensitive data remains protected during presentations and meetings.

In conclusion, the AMX MAX-CSE and MAX-CSD 10 multimedia presentation systems stand out in the market due to their superior audio and video quality, user-friendly features, and extensive connectivity options. They are ideal solutions for professionals seeking to leverage technology for more productive and engaging communication.