Samsung M8 manual Table of Tables

Page 6

TABLE OF TABLES

 

Table 3-1 : Specifications

6

Table 3-2 : Physical Specifications

7

Table 3-3 : Logical Configurations

7

Table 3-4 : Performance Specifications

8

Table 3-5 : Power consumption

9

Table 3-6 : Environmental Specifications

10

Table 3-7 : Reliability Specifications

12

Table 4-1 SATA Connector Pin Definitions

19

Table 7-1 Phy Event Counter Supports

45

Table 8-1 Command Code Parameters

47

Table 8-2 Device Configuration Overlay Feature Register Values

49

Table 8-3 Device Configuration Identify data structure

50

Table 8-4 Diagnostic Codes

51

Table 8-5 IDENTIFY DEVICE information

52

Table 8-6 Automatic Standby Timer Periods

57

Table 8-7 Security password content

61

Table 8-8 Security Erase Unit Password

62

Table 8-9 Security Set Password data content

62

Table 8-10 Identifier and security level bit interaction

63

Table 8-11 Set Features Register Definitions

64

Table 8-12 Transfer Mode Values

64

Table 8-13 Set Max Feature Register Values

65

Table 8-14 SMART Feature Registers Values

66

Table 8-15 Device SMART Data Structure

68

Table 8-16 SMART Attribute Status Flags

69

Table 8-17 SMART Attribute Data List

71

Table 8-18 Off-line Data Collection Status Values

71

Table 8-19 Self-test Execution Status Values

72

Spinpoint M8 Product Manual REV 2.3

Image 6
Contents M8 Product Manual Page Table of Contents Servo System Read and Write Operations Read Fpdma Queued 60h Read Log Extended 2Fh Read Long 22h Table of Tables Scope User DefinitionManual Organization Sata ReferenceDescription IntroductionKey Features Standards and Regulations Hardware RequirementsSpecifications SpecificationsSpecification Summary Spindle speed RPM RPM ClassPhysical Specifications Physical SpecificationsLogical Configurations Physical dimensionsPerformance Specifications Power Requirements Power consumptionPower consumption RatedEnvironmental Specifications Environmental Specifications15.0 Reliability Specifications Installation Space RequirementsUnpacking Instructions MountingMounting Dimensions OrientationClearance Mounting-Screw ClearanceCable Connectors VentilationSata Connectivity Serial ATA Power ManagementHDD Power, Sata Interface, and Factory Jumper Connector Pin Locations on the Drive Pcba Drive Installation DC Power Connector and SATA-Bus Interface Cable ConnectionsDC Spindle Motor Assembly Head / Disk Assembly HDABase Casting Assembly Disk Drive OperationCoverAssembly Voice Coil Motor and Actuator Latch Assemblies Disk Stack AssemblyHead Stack Assembly Air Filtration SystemDigital Signal Process and Interface Controller Drive ElectronicsDisk Controller DDR Host Interface Control Block Buffer Control BlockDisk Control Block Disk Ldpc Control BlockFrequency Synthesizer Time Base Generator Power ManagementRead/Write IC Automatic Gain ControlAnalog Anti-Aliasing Low Pass Filter Analog to Digital Converter ADC and FIRServo System Read and Write OperationsRead Channel Firmware Features Write ChannelRead Caching Write Caching Multi-burst ECC Correction Defect ManagementAutomatic Defect Allocation SmartSata II Interface Sata TerminologySpinpoint M8 Product Manual REV Physical Interface Signal Summary Signal DescriptionsControl Block Register Descriptions When read When written2 I/O Register Address RegistersError Register Ex F1h Command Block Register DescriptionsFeatures Register and Feature Extended Register Ex F1h Device Control Register ex F6hCommand Register Ex F7h Device Register Ex F6hStatus Register Ex F7h Staggered Spin-up Disable Control Sata II Feature SETDevice Activity Signal Auto-Activate in DMA Setup FISPhy. Event Counters Software Settings Preservation Sata Power ManagementATA Command Descriptions Command TableCommand Code Parameters Command Descriptions Check Power Mode E5hCommand Device Configuration Overlay B1hDevice Configuration Overlay Feature Register Values Download Micro Code 92hDevice Configuration Identify data structure Word Content Flush Cache E7h, EAh extended Execute Device Diagnostics 90hDiagnostic Codes Format Track 50hContent Description Identify Device information=the fields reported in word 88 are valid EXT =Media Card Pass Through command feature set supported Word Content Description WWNAutomatic Standby Timer Periods Idle E3hIdle Immediate E1h Read Buffer E4h Initialize Device Parameters 91hNOP 00h Read DMA C8h, 25h extendedRead Multiple Command C4h, 29h extended Read Log Extended 2FhRead Long 22h Read Native Max Address F8h, 27h extended Read Sectors 20h, 24h extendedRead Verify Sectors 40h, 41h extended Security Erase Prepare F3h Security Disable Password F6hRecalibrate 10h Security Erase Unit F4hSecurity Set Password data content Security Set Password F1hSecurity Erase Unit Password Word Content Security Freeze Lock F5hSecurity Unlock F2h Set Features EFhIdentifier Level Command result Seek 7xh11 Set Features Register Definitions 12 Transfer Mode ValuesSet Max Address F9h, 37h extended Set Multiple Mode C6h13 Set Max Feature Register Values Sleep E6hSmart enable/disable attribute auto-save D2h 14 Smart Feature Registers ValuesSmart disable operations D9h Smart B0hSmart enable operations D8h Smart execute off-line immediate D4hSmart read data D0h 15 Device Smart Data StructureData Structure Revision Number Bit Name Description 16 Smart Attribute Status Flags17 Smart Attribute Data List 18 Off-line Data Collection Status ValuesSelf-test execution status byte 19 Self-test Execution Status ValuesSmart read log sector D5h Smart return status DAhSmart write log sector D6h Write DMA CAh, 35h extended Standby Immediate E0hWrite Buffer E8h Write Fpdma Queued 61hWrite Multiple Command C5h, 39h extended Write Long 32hWrite Sectors 30h, 34h extended Spinpoint M8 Product Manual REV Maintenance Maintenance PrecautionsGeneral Information HDD handling guide -Please handle HDD by side surfaces Service and Repair HDD handling guide Prevent Shocks