Samsung M8 manual Idle E3h, Idle Immediate E1h, Automatic Standby Timer Periods

Page 62

Word	Content			Description
		2	1=	Security locked
		1	1=	Security enabled
		0	1=	Security supported
129-159	0000h	Vendor specific
160	0000h	CFA power mode 1
161-175	0000h	Reserved for CFA
176-205	0000h	Current media serial number
206-254	0000h	Reserved
255	xxxxh	Integrity word
		15-8	Checksum
		5	Signature (A5h)

8.2.8Idle (E3h)

This command causes the drive to enter the Idle Mode, clear BSY, and generate an interrupt. The interrupt is generated even though the drive may not have fully transitioned to Idle Mode.

If the drive is already spinning, the spin-up sequence is not executed.

If the Sector Count register is non-zero, then the automatic Idle Mode sequence is enabled, and the timer begins counting down immediately. If the Sector Count register is zero, the automatic power down sequence is disabled.

After the drive enters Idle Mode, it automatically transitions to Standby Mode upon expiration of a prescribed 1 minute spin-down timer.

Table 8-6 Automatic Standby Timer Periods

Sector Count Register Contents		Corresponding Time-Out Period
0	(00h)	Timeout Disabled

1-240 (01h-FOh)		(value * 5) seconds

241-251	(F1h-FBh)	(value - 240) * 30 minutes

252	(FCh)	21 minutes

253	(FDh)	8 hours

254	(FEh)	Reserved

255	(FFh)	21 minutes 15 seconds

8.2.9Idle Immediate (E1h)

This command causes the drive to enter Idle Mode, clear BSY, and generate an interrupt. The interrupt is generated even though the drive may not have fully transitioned to Idle Mode.

Spinpoint M8 Product Manual REV 2.3

56

Image 62

Contents M8 Product Manual Page Table of Contents Servo System Read and Write Operations Read Fpdma Queued 60h Read Log Extended 2Fh Read Long 22h Table of Tables Manual Organization ScopeUser Definition Sata ReferenceDescription IntroductionKey Features Standards and Regulations Hardware RequirementsSpecifications SpecificationsSpecification Summary Spindle speed RPM RPM ClassPhysical Specifications Physical SpecificationsLogical Configurations Physical dimensionsPerformance Specifications Power Requirements Power consumptionPower consumption RatedEnvironmental Specifications Environmental Specifications15.0 Reliability Specifications Installation Space RequirementsUnpacking Instructions MountingMounting Dimensions OrientationClearance Mounting-Screw ClearanceSata Connectivity Cable ConnectorsVentilation Serial ATA Power ManagementHDD Power, Sata Interface, and Factory Jumper Connector Pin Locations on the Drive Pcba Drive Installation DC Power Connector and SATA-Bus Interface Cable ConnectionsDC Spindle Motor Assembly Head / Disk Assembly HDABase Casting Assembly Disk Drive OperationCoverAssembly Voice Coil Motor and Actuator Latch Assemblies Disk Stack AssemblyHead Stack Assembly Air Filtration SystemDisk Controller Digital Signal Process and Interface ControllerDrive Electronics DDR Host Interface Control Block Buffer Control BlockFrequency Synthesizer Disk Control BlockDisk Ldpc Control Block Time Base Generator Power ManagementRead/Write IC Automatic Gain ControlAnalog Anti-Aliasing Low Pass Filter Analog to Digital Converter ADC and FIRRead Channel Servo SystemRead and Write Operations Read Caching Firmware FeaturesWrite Channel Write Caching Multi-burst ECC Correction Defect ManagementAutomatic Defect Allocation SmartSata II Interface Sata TerminologySpinpoint M8 Product Manual REV Physical Interface Signal Summary Signal DescriptionsControl Block Register Descriptions When read When written2 I/O Register Address RegistersError Register Ex F1h Command Block Register DescriptionsFeatures Register and Feature Extended Register Ex F1h Device Control Register ex F6hCommand Register Ex F7h Device Register Ex F6hStatus Register Ex F7h Staggered Spin-up Disable Control Sata II Feature SETDevice Activity Signal Auto-Activate in DMA Setup FISPhy. Event Counters Software Settings Preservation Sata Power ManagementCommand Code Parameters ATA Command DescriptionsCommand Table Command Descriptions Check Power Mode E5hCommand Device Configuration Overlay B1hDevice Configuration Overlay Feature Register Values Download Micro Code 92hDevice Configuration Identify data structure Word Content Flush Cache E7h, EAh extended Execute Device Diagnostics 90hDiagnostic Codes Format Track 50hContent Description Identify Device information=the fields reported in word 88 are valid EXT =Media Card Pass Through command feature set supported Word Content Description WWNIdle Immediate E1h Automatic Standby Timer PeriodsIdle E3h Read Buffer E4h Initialize Device Parameters 91hNOP 00h Read DMA C8h, 25h extendedRead Long 22h Read Multiple Command C4h, 29h extendedRead Log Extended 2Fh Read Verify Sectors 40h, 41h extended Read Native Max Address F8h, 27h extendedRead Sectors 20h, 24h extended Security Erase Prepare F3h Security Disable Password F6hRecalibrate 10h Security Erase Unit F4hSecurity Set Password data content Security Set Password F1hSecurity Erase Unit Password Word Content Security Freeze Lock F5hSecurity Unlock F2h Set Features EFhIdentifier Level Command result Seek 7xh11 Set Features Register Definitions 12 Transfer Mode ValuesSet Max Address F9h, 37h extended Set Multiple Mode C6h13 Set Max Feature Register Values Sleep E6hSmart enable/disable attribute auto-save D2h 14 Smart Feature Registers ValuesSmart disable operations D9h Smart B0hSmart enable operations D8h Smart execute off-line immediate D4hSmart read data D0h 15 Device Smart Data StructureData Structure Revision Number Bit Name Description 16 Smart Attribute Status Flags17 Smart Attribute Data List 18 Off-line Data Collection Status ValuesSelf-test execution status byte 19 Self-test Execution Status ValuesSmart write log sector D6h Smart read log sector D5hSmart return status DAh Write DMA CAh, 35h extended Standby Immediate E0hWrite Buffer E8h Write Fpdma Queued 61hWrite Sectors 30h, 34h extended Write Multiple Command C5h, 39h extendedWrite Long 32h Spinpoint M8 Product Manual REV General Information MaintenanceMaintenance Precautions HDD handling guide -Please handle HDD by side surfaces Service and Repair HDD handling guide Prevent Shocks