Samsung M8 manual Smart enable operations D8h, Smart execute off-line immediate D4h

Page 72

A value of F1h written by the host into the device’s Sector Count Register before issuing this command shall cause this feature to be enabled. Any other meaning of this value or any other non-zero value written by the host into this register before issuing this command may differ from device to device.

8.2.34.3Smart enable operations (D8h)

This command enables all SMART capabilities within the device. Prior to receipt of this command SMART data are neither monitored nor saved by the device. The state of SMART (either enabled or disabled) shall be preserved by the device across power cycles. Once enabled, the receipt of subsequent SMART ENABLE OPERATIONS commands shall not affect any SMART data or functions.

8.2.34.4Smart execute off-line immediate (D4h)

This command causes the device to immediately initiate the activities that collect SMART data in an off-line mode and then save this data to the device’s non-volatile memory.

During execution of its off-line activities the device shall not set BSY nor clear DRDY.

If the device is in the process of performing its set of off-line data collection activities (as a result of receiving a SMART EXECUTE OFF-LINE IMMEDIATE command from the host), and is interrupted by any new command from the host except a SMART DISABLE OPERATIONS, SMART EXECUTE OFF-LINE IMMEDIATE, or STANDBY IMMEDIATE command, the device shall suspend or abort its off-line data collection activities and service the host within two seconds after receipt of the new command. After servicing the interrupting command from host the device may immediately re-initiate or resume its off-line data collection activities without any additional commands from host

If the device is in the process of performing its off-line data collection activities and is interrupted by a STANDBY IMMEDIATE command from the host, the device shall suspend or abort its off-line data collection activities, and service the host within two seconds after receipt of the command. After receiving a new command that causes the device to exit a power saving mode, the device shall initiate or resume off-line data collection activities without any additional commands from the host unless the device aborted these activities.

If the device is in the process of performing its off-line data collection activities and is interrupted by a SMART DISABLE OPERATIONS command from the host, the device shall suspend or abort its off-line data collection activities and service the host within two seconds after receipt of the command. Upon receipt of the next SMART ENABLE OPERATIONS command the device may, after the next vendor specified event, either re-initiate its off-line data collection activities or resume those activities from where they had been previously suspended.

If the device is in the process of performing its off-line data collection activities and is interrupted by a SMART EXECUTE OFF-LINE IMMEDIATE command from the host, the device shall abort its off-line data collection activities and service the host within two seconds after receipt of the command. The device shall then re-initiate its off-line data collection activities in response to the new EXECUTE OFF-LINE IMMEDIATE command.

Spinpoint M8 Product Manual REV 2.3

66

Image 72
Contents M8 Product Manual Page Table of Contents Servo System Read and Write Operations Read Fpdma Queued 60h Read Log Extended 2Fh Read Long 22h Table of Tables Scope User DefinitionManual Organization Sata ReferenceDescription IntroductionKey Features Standards and Regulations Hardware RequirementsSpecifications Specification SummarySpecifications Spindle speed RPM RPM ClassPhysical Specifications Logical ConfigurationsPhysical Specifications Physical dimensionsPerformance Specifications Power consumption Power consumptionPower Requirements RatedEnvironmental Specifications Environmental Specifications15.0 Reliability Specifications Installation Space RequirementsUnpacking Instructions MountingMounting Dimensions OrientationClearance Mounting-Screw ClearanceCable Connectors VentilationSata Connectivity Serial ATA Power ManagementHDD Power, Sata Interface, and Factory Jumper Connector Pin Locations on the Drive Pcba Drive Installation DC Power Connector and SATA-Bus Interface Cable ConnectionsHead / Disk Assembly HDA Base Casting AssemblyDC Spindle Motor Assembly Disk Drive OperationCoverAssembly Disk Stack Assembly Head Stack AssemblyVoice Coil Motor and Actuator Latch Assemblies Air Filtration SystemDigital Signal Process and Interface Controller Drive ElectronicsDisk Controller DDR Host Interface Control Block Buffer Control BlockDisk Control Block Disk Ldpc Control BlockFrequency Synthesizer Power Management Read/Write ICTime Base Generator Automatic Gain ControlAnalog Anti-Aliasing Low Pass Filter Analog to Digital Converter ADC and FIRServo System Read and Write OperationsRead Channel Firmware Features Write ChannelRead Caching Write Caching Defect Management Automatic Defect AllocationMulti-burst ECC Correction SmartSata II Interface Sata TerminologySpinpoint M8 Product Manual REV Physical Interface Signal Summary Signal DescriptionsWhen read When written 2 I/O Register AddressControl Block Register Descriptions RegistersCommand Block Register Descriptions Features Register and Feature Extended Register Ex F1hError Register Ex F1h Device Control Register ex F6hCommand Register Ex F7h Device Register Ex F6hStatus Register Ex F7h Sata II Feature SET Device Activity SignalStaggered Spin-up Disable Control Auto-Activate in DMA Setup FISPhy. Event Counters Software Settings Preservation Sata Power ManagementATA Command Descriptions Command TableCommand Code Parameters Command Descriptions Check Power Mode E5hDevice Configuration Overlay B1h Device Configuration Overlay Feature Register ValuesCommand Download Micro Code 92hDevice Configuration Identify data structure Word Content Execute Device Diagnostics 90h Diagnostic CodesFlush Cache E7h, EAh extended Format Track 50hContent Description Identify Device information=the fields reported in word 88 are valid EXT =Media Card Pass Through command feature set supported Word Content Description WWNAutomatic Standby Timer Periods Idle E3hIdle Immediate E1h Initialize Device Parameters 91h NOP 00hRead Buffer E4h Read DMA C8h, 25h extendedRead Multiple Command C4h, 29h extended Read Log Extended 2FhRead Long 22h Read Native Max Address F8h, 27h extended Read Sectors 20h, 24h extendedRead Verify Sectors 40h, 41h extended Security Disable Password F6h Recalibrate 10hSecurity Erase Prepare F3h Security Erase Unit F4hSecurity Set Password F1h Security Erase Unit Password Word ContentSecurity Set Password data content Security Freeze Lock F5hSet Features EFh Identifier Level Command resultSecurity Unlock F2h Seek 7xh11 Set Features Register Definitions 12 Transfer Mode ValuesSet Multiple Mode C6h 13 Set Max Feature Register ValuesSet Max Address F9h, 37h extended Sleep E6h14 Smart Feature Registers Values Smart disable operations D9hSmart enable/disable attribute auto-save D2h Smart B0hSmart enable operations D8h Smart execute off-line immediate D4hSmart read data D0h 15 Device Smart Data StructureData Structure Revision Number Bit Name Description 16 Smart Attribute Status Flags17 Smart Attribute Data List 18 Off-line Data Collection Status ValuesSelf-test execution status byte 19 Self-test Execution Status ValuesSmart read log sector D5h Smart return status DAhSmart write log sector D6h Standby Immediate E0h Write Buffer E8hWrite DMA CAh, 35h extended Write Fpdma Queued 61hWrite Multiple Command C5h, 39h extended Write Long 32hWrite Sectors 30h, 34h extended Spinpoint M8 Product Manual REV Maintenance Maintenance PrecautionsGeneral Information HDD handling guide -Please handle HDD by side surfaces Service and Repair HDD handling guide Prevent Shocks