Calibre UK VANTAGE-HD manual Environmental and Safety, Safety Warning

Page 30

ENVIRONMENTAL AND SAFETY

14.1.

Operating

 

 

Temperature

0oC to 40oC (32°F to 104°F)

 

Humidity (non condensing)

0% to 95%

14.2.

Storage

 

 

Temperature

-25oC to 85oC (-13°F to 185°F)

 

Humidity (non condensing)

0% to 95%

14.3.Safety Issues

SAFETY WARNING:

1.THERE ARE NO USER SERVICEABLE PARTS WITHIN THE UNIT, THE REMOTE CONTROL OR THE MAINS POWER SUPPLY. DO NOT REMOVE THE POWER SUPPLY COVER - DANGEROUS VOLTAGES WILL BE EXPOSED. DO NOT OPERATE VANTAGE-HD WITH ITS COVER REMOVED.

2.ENSURE THAT ALL ELECTRICAL CONNECTIONS (INCLUDING THE POWER CORD AND ANY EXTENSION LEADS) ARE PROPERLY MADE AND COMPLY WITH ELECTRICAL SAFETY REGULATIONS APPLICABLE TO YOUR LOCATON.

3.ENSURE THAT THE INTEGRITY OF THE EQUIPMENT ISOLATION BARRIER IS MAINTAINED WHEN CONNECTING TO OTHER EQUIPMENT. THIS MEANS THAT ONLY LOW VOLTAGE ISOLATED CIRCUITS MAY BE CONNECTED TO THE SIGNAL INPUTS AND OUTPUTS. IF ANY DOUBT EXISTS CONSULT QUALIFIED SERVICE PERSONNEL.

4.TO PREVENT SHOCK OR FIRE HAZARD DO NOT EXPOSE THIS EQUIPMENT TO RAIN OR MOISTURE. IF SUCH EXPOSURE OCCURS, REMOVE THE PLUG FROM THE MAINS OUTLET AND HAVE THE EXPOSED UNIT CHECKED BY QUALIFIED SERVICE PERSONNEL.

5.VANTAGE-HD IS DESIGNED FOR NORMAL DOMESTIC USE IN A DRY ENVIRONMENT. DO NOT USE OUTSIDE, OR IN AREAS OF HIGH HUMIDITY SUCH AS IN THE VANCINITY OF KITCHEN APPLIANCES, IN THE BATHROOM OR SHOWER ROOM, SAUNA, STEAM ROOM, SWIMMING POOL OR ANY OTHER DAMP ENVIRONMENT. USE IN A DAMP ENVIRONMENT MAY CAUSE DAMAGE TO VANTAGE-HD AND IS DANGEROUS.

6.DO NOT CONTINUE TO OPERATE THE EQUIPMENT IF YOU HAVE ANY DOUBT ABOUT IT WORKING NORMALLY, OR IF IT IS DAMAGED IN ANY WAY. WITHDRAW THE MAINS PLUG FROM THE MAINS OUTLET AND CONSULT QUALIFIED SERVICE PERSONNEL.

7.DO NOT REMOVE ANY FIXED COVERS UNLESS YOU ARE QUALIFIED TO DO SO AND EVEN THEN WITHDRAW THE MAINS PLUG FROM THE MAINS OUTLET BEFORE YOU START.

8.THE COVER OF VANTAGE-HD SHOULD ONLY BE REMOVED FOR INSTALLATION OF UPGRADE BOARDS AND EVEN THEN ONLY ONCE DISCONNECTED FROM THE POWER SUPPLY AND ALL ASSOCIATED EQUIPMENT. DO NOT ATTEMPT TO INSTALL AN UPGRADE BOARD UNLESS YOU ARE CONFIDENT OF YOUR ABILITY TO DO SO AND YOU ARE WEARING A GROUNDED ANTI- STATIC WRISTBAND. DAMAGE CAUSED DURING UPGRADES OR WITH THE COVER REMOVED IS NOT COVERED UNDER THE LIMITED WARRANTY.

9.TO AVOID DANGER OF EXPLOSION, DO NOT OPERATE THIS EQUIPMENT IN AN EXPLOSIVE ATMOSPHERE

Issue 1.0.2

28 March 2006 © Calibre UK Ltd

Page 27 of 30

Image 30
Contents VANTAGE-HD Copyright & Limited Warranty Welcome to the Vantage-HD ManualContents Product Description Below details the connections to Vantage-HD Connecting VANTAGE-HD to the Display Device Switch on Connect PowerConfigure Output modeSelect display Device resolution Image Select OutputFrame Rate ProjectionOptimize Display Device Setup Pixel Clock and Phase Adjustments Within the DisplayWarp Correction Setting AudioDelay Mode GammaConnecting VANTAGE-HD Inputs Reset Channel Freeing Input Channels Selecting AN Input Adjusting AN Input Pixel Clock & PhaseVideo input signals only MpegBlack Level Color temperatureInput gamma mode Input CapturePositioning the PIP Picture in PictureSelecting the input OSD not visiblePicture In Picture Menu Issue Input Source Information MenuVantage-HD Information Vantage revision Input FormatConfiguration Menu 0SD Timeout Infoscreen TimeoutFactory Reset Output Mode Details VBPPage Input Signal Details NTSC, PAL, SecamPage Power Supply Specification Regulatory Approvals Environmental and Safety Safety WarningHdmi Connection Advice Issue Warranty & Service Advice