INTRODUCTION
CONTROLS, CONNECTORS AND INDICATORS
Front panel
1 2 34 |
|
|
|
| 567 |
|
|
| 8 9 | 0 | ! | |
|
|
|
|
|
|
|
|
|
| REMOTE CONTROL UNIT | ||
TALLY CALL FULL AUTO | F1 | F3 | MENU/SHUTTER | GAIN |
| PAINT WHITE | AUTO |
| MASTER BLACK | IRIS | POWER | |
|
| SHUTTER |
|
|
| STEP |
|
| W.BAL |
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||
|
|
|
|
|
| HIGH |
|
| B |
|
| I |
|
|
|
|
|
|
|
|
|
|
|
| |
|
|
|
| SHUTTER | VARIABLE | MID |
|
| A | AUTO |
|
|
BARS | F2 | F4 | MENU | LOW | R | B | PRESET | MANU |
|
| ||
|
|
|
| |||||||||
|
| GAIN |
|
|
|
|
|
|
|
|
| O |
|
|
|
|
|
|
|
|
|
|
|
| |
INTERCOM | DOWN UP | DOWN UP | CLOSE | OPEN |
LEVEL |
|
|
|
|
¤ ⁄ |
|
|
|
|
) ( | *& ^ | % $ # @ | ||
1 Intercom jack |
|
| 6 [GAIN] lamp | |
Connect the intercom headset to this jack.
REF. : “Intercom” on page 14.
This lamp lights when the gain control is in the VARIABLE GAIN mode.
2[INTERCOM LEVEL] control
Use this knob to adjust the intercom earphone volume.
3[TALLY] lamp
This lamp lights when a signal is input to the TALLY termi- nals 2 on the rear panel.
It lights in red when a tally signal is input to the TALLY PGM terminal on the rear panel or in green when a tally signal is input to the TALLY PVW terminal. It blinks in red when there is a CALL signal from the camera.
NOTE
The order of priority among the above signals are; CALL (red blinking), TALLY PGM (red lighting) then TALLY PVW (green lighting).
4[CALL] button (with lamp)
The camera operator can also be called without using the intercom. When this button is pressed once, the button lamp lights up and the tally lamp on the camera blinks to inform the camera operator of a call. Pressing this button again turns off both the button lamp and tally lamp on the camera.
NOTE
When the CALL button is pressed during
5[GAIN - VARIABLE] control with ON/OFF button
When the button is pressed, the VARIABLE GAIN mode is switched ON and OFF alternately.
The GAIN lamp 6lights when the VARIABLE GAIN mode is ON.
When the GAIN mode is set to VARIABLE, the GAIN value can be varied from 0.1 dB (or 1.0 dB) to 18 dB in 0.1 dB (or 1.0 dB) steps. The variation per step and the maximum gain value can be changed under the following items.
REF. : Items “5B: V. GAIN STEP” and “5C: V. GAIN
MAX” on page 25.
7[GAIN - STEP LOW/MID/HIGH] switch
The gain value can be selected according to the position of this switch.
HIGH : REF. Gain value set by item “5F: GAIN HIGH” on page 25.
MID : REF. Gain value set by item “5E: GAIN MID” on page 25.
LOW : REF. Gain value set by item “5D: GAIN LOW” on page 25.
The selected gain value is shown in the LCD display ) every time that the position of this switch is changed.
8[MASTER BLACK] control
Use this knob to adjust the pedestal level, which is the black reference (master black) value.
9[IRIS - AUTO/MANU] button (with lamp)
When this button is pressed so that the lamp in it lights the lens iris is set to the manual iris control mode. The lens iris level may be adjusted in this mode by using the IRIS con- trol 0.
When this button is pressed so that the lamp in it turns off, the lens iris is set to the auto iris control mode.The auto iris level can be fine adjusted with the IRIS control 0.
0[IRIS - CLOSE-OPEN] control
When the manual iris control mode is set (which is indi- cated by the lighting of the lamp in the AUTO/MANU but- ton 9), use this knob to adjust the iris aperture between CLOSE and OPEN.
When the iris mode is AUTO (when the lamp in the button is not lit up), the auto iris level can be fine adjusted with this knob.
REF. “Iris Adjustment” on page 17.
5