JVC SR-MV55U DV Dubbing DVD Deck Only, Performing dubbing without using the DV Dubbing controller

				EDITING EN 51
	DV Dubbing (DVD Deck Only)		1 Connect a DV camcorder or DV equipment to the [DV IN]
			connector on the unit’s front panel.
			2 Load a DVD-RAM/RW/R disc on the unit.
You can dub programs from a DV camcorder or DV equipment
			3 Press VCR/DVD repeatedly so that the DVD lamp lights up on
connected to the unit with a DV cable. The unit’s remote control
allows you the limited control of the connected DV camcorder or			the unit.
DV equipment functions during dubbing.			4 Press INPUT SELECT +/– on the unit or INPUT +/– on the
			remote control to set the input to “DV”.
NOTES:			● The “DV DUBBING” controller appears on the TV screen.
● Use the DV cable VC-VDV 204U for connection.			● If “	” does not appear on the “DV DUBBING” controller, make
● When you connect a PC to the [DV IN] connector, we do not			sure the DV equipment is connected correctly.
		assure the normal operation of this unit.	5 Press REC MODE repeatedly to set the recording mode.
			( pg. 36)
		Your unit	6 Locate the point from where you want to start dubbing, then
			stop or pause playback by pressing the following buttons on the
			remote control: 4, 5, 3, 8, 9

● To play back in slow speed (1/10 of the normal speed), press 9 to pause playback, then press 3 or 5.

● To play back frame-by-frame, press 9 to pause playback, then press 9 repeatedly. Each press of 9 advances a frame.

● To change the playback direction, press 3 or 5.

To [DV IN]	7 Press w e to select	, then press ENTER.
	8 Press rt to select the desired
	sound track, then press ENTER.
	AUDIO 1: Select this to record the
	original stereo sound played
DV Camcorder	back on the connected DV
	equipment.
DV cable	AUDIO 2: Select this to record the
(VC-VDV 204U)	dubbed stereo sound played
(not supplied)	back on the connected DV
	equipment.
	MIX: Select this to record the sound of both “AUDIO 1” and
DV connector	“AUDIO 2”.
	● Note that this selection is not available when the source program is
	recorded in 16BIT (48 kHz) mode.
DV equipment	9 Press w e to select	, then press ENTER. The
	dubbing starts.
	● Playback on the external DV equipment and recording on the unit
	should start simultaneously.
	● When the playback from the beginning is not possible, the “DV
	DUBBING” controller cannot be used. Perform dubbing without using
	the “DV DUBBING” controller. ( below)
	● To pause dubbing, press w e to select		, then press
	ENTER. Both the unit and the external DV equipment pause dubbing.
	Pressing 9 on the unit also works the same way.
	● To clear the “DV DUBBING” controller from the TV screen, press ON
	SCREEN.

10 Press 8 on the remote control to stop dubbing.

● Both the unit and the external DV equipment stop dubbing.

NOTES:

● Dubbing copyright guarded programs is not possible.

● Original DV information such as the recording date and time are not recorded.

● The superimposed indication during the operation or dubbing is not recorded.

● It is not possible to perform dubbing when the dubbing (DUBB.) lamp lights up on the unit. Press VCR]DVD so that the dubbing (DUBB.) lamp lights off.

Performing dubbing without using the “DV DUBBING” controller

A Press INPUT SELECT +/– on the unit or INPUT +/– on the remote control to set the input to “DV”.

B Press REC MODE repeatedly to set the recording mode. ( pg. 36)

C Start playback on the external DV equipment slightly before the actual point from where you wish to start dubbing.

D Press 7 on the unit to start recording. Or while holding 7, press 4 on the remote control. The dubbing starts.

E When the dubbing ends, press 8 on the unit, then stop playback on the external DV equipment.