SUBSIDIARY SETTINGS EN 61
8 PICTURE CONTROL — AUTO / EDIT / SOFT / SHARP | 8 BLUE BACK — ON / OFF |
This feature helps you to adjust the playback picture quality according to your preference. Normally select “AUTO”. AUTO: Picture quality is adjusted automatically.
EDIT: Minimizes picture degradation during editing (recording and playback).
SOFT: Reduces image coarseness when viewing overplayed tapes containing a lot of noise.
SHARP: Clearer,
NOTES:
●When you select “EDIT”, “SOFT” or “SHARP”, the selected mode will not change until you select another mode.
●When you select “EDIT” to dub tapes, be sure to select “NORM” after you finish dubbing the tapes.
●When “VIDEO CALIBRATION” is “OFF”, “PICTURE CONTROL” switches automatically from “AUTO” to “NORM”.
When this function is set to “ON”, the TV screen becomes all blue when there is no signal input from the external input.
NOTE:
When you want to receive an unstable external input with poor signals, set this function to “OFF”.
8S-VHS MODE — ON / OFF
Your unit can record in
To record in S-VHS:
Set
To record in S-VHS ET on a VHS cassette:
Set
8VIDEO STABILIZER — ON / OFF
When this function is set to “ON”, you can automatically correct vertical vibration in the picture when playing back unstable recordings made on another recorder.
NOTES:
●When you finish viewing a tape, be sure to set this function to “OFF”.
●Regardless of the setting, this function has no effect during recording and during special effects playback.
●The
●To watch recordings with
8SUPERIMPOSE — AUTO / ON / OFF
When this function is set to “AUTO”, various operational indicators appear on the TV screen.
AUTO: To superimpose operational indications for approximately five seconds just after the corresponding operation.
ON: Functions in the same way as “AUTO”. However, when “ON” is selected, the counter display ( pg. 14) will always be displayed during playback.
OFF: To turn off superimposed indications.
NOTES:
●When you use this unit as the source player for editing, be sure to set “SUPERIMPOSE” to “OFF” before starting.
●During playback, the operation mode indicators may be disturbed depending on the type of tape being used.
To record in VHS:
Insert a cassette marked “VHS”.
Set
The VHS recording mode is automatically selected regardless of the
To record in VHS on an S-VHS cassette:
Insert a cassette marked
The VHS recording mode is selected.
NOTE:
When playing back a tape that has been recorded in
8RETURN POINT — TAPE END / REC END
Returning point for Playback or Repeat Play can be set to tape end or recording end. (This unit considers
REC END: Playback stops at the end of the recording.
NOTE:
The setting you have made is kept in memory. Even if this unit is unplugged or power failure occurs, it will resume every time you turn on this unit. ( pg. 65)
8DIGITAL R3 — ON / OFF
When this function is set to “ON”, the Digital 3R picture system applies edge correction to the luminance signal to enhance detail.
NOTES:
●Normally it is recommended to keep “DIGITAL 3R” set to “ON”.
●Depending on the type of tape being used, picture quality may be better with “DIGITAL 3R” set to “OFF”.
●If you use the unit as the source player for editing, be sure to set “DIGITAL 3R” to“OFF” before starting.
8 REC SAFETY — ON / OFF
Usually, you can only record onto a cassette with its record safety tab intact. When this function is set to “OFF”, recording can be done onto a cassette with its record safety tab removed.
NOTES:
●The setting you have made is kept in memory. Even if this unit is unplugged or power failure occurs, it will resume every time you turn on this unit. ( pg. 65)
●When “REC SAFETY” is set to “OFF”, playback does not start automatically when you insert a cassette with its record safety tab removed. ( pg. 36)