JVC LPT0923-001A manual On The Front Display Panel, Link Functions

20 EN INITIAL SETTINGS

Results Of Auto Set Up/Preset Download Appearing	INFORMATION
On The Front Display Panel	Language for the on-screen display
	Auto Set Up also selects the language automatically for the on-
	screen display depending on the Country setting you have made in
If both Auto Channel Set and
	step 2 on page 18 (unless you have selected BELGIUM or
Auto Clock Set have been	SUISSE), as shown below.
performed successfully, the
correct current time is displayed.	SUOMI	] SUOMI	ITALIA	] ITALIANO
Turn on the TV and select its AV mode, then make sure that all	PORTUGAL	] ENGLISH	MAGYARORSZÁG	] ENGLISH
necessary stations have been stored in the unit’s memory by using	DEUTSCHLAND	] DEUTSCH	ESPAÑA	] CASTELLANO
the PR +/– button(s).
	POLSKA	] ENGLISH	NEDERLAND	] NEDERLANDS
● If station names (ID –  pg. 85) have also been stored in the unit’s
	NORGE	] NORSK	GREECE	] ENGLISH
memory, the station name will be displayed at the top right corner of
	SVERIGE	] SVENSKA	OTHER WESTERN ] ENGLISH
the TV screen for about 5 seconds when the unit is tuned to a
	DANMARK	] DANSK
different station.
	ÖSTERREICH	] DEUTSCH
● If you want to set the tuner manually such as to add or skip channels,			OTHER EASTERN	] ENGLISH
	ČESKÁ REPUBLIKA ] ENGLISH
to change channel positions, or to set or change station names, see
pages 71 – 72.	If you want to change the language setting manually, see “On-
If Auto Channel Set has	screen Language Set” on page 21.
succeeded but Auto Clock Set	Just Clock
has not, “PR 1” (channel	Your unit is equipped with the Just Clock function which provides
position) is displayed.	accurate time keeping through automatic adjustments at regular
OR	intervals, by reading data from a PDC signal. If you want to take
If both Auto Channel Set and Auto Clock Set have failed,	advantage of this function, simply set it to “ON”. ( pg. 73)
“– –:– –” is displayed.

ATurn on the TV and select its AV mode, then make sure that all necessary stations have been stored in the unit’s memory by

using the PR +/– button(s).

●If station names (ID –  pg. 85) have also been stored in the unit’s memory, the station name will be displayed at the top right corner of the TV screen for about 5 seconds when the unit is tuned to a different station.

●If you want to set the tuner manually such as to add or skip channels, to change channel positions, or to set or change station names, see pages 71 – 72.

BPerform “Clock Set” on page 73.

ATTENTION:

After making sure the cables are connected properly, turn off the unit’s power once, then turn the unit’s power back on again.

The Country Set display appears on the TV screen; perform “Auto Set Up” on page 18 or “Preset Download” on page 19 again.

IMPORTANT:

●To check if the Guide Program numbers have been set correctly, perform the SHOWVIEW Timer Programming. ( pg. 44)

●In certain reception conditions, station names may not be stored correctly, and auto Guide Program Number Set may not work properly. If the Guide Program numbers are not set properly when you timer-record a TV programme using the SHOWVIEW system, the unit will record a TV programme of a different station. When programming the timer using the SHOWVIEW system, be sure to check the desired channel is selected correctly. ( pg. 44, “SHOWVIEWTM Timer Programming”)

●Your unit memorizes all detected stations even if reception of some of them is poor. You can delete those stations with an unacceptable picture. ( pg. 72, “Delete A Channel”)

T-V Link Functions

When you connect the unit to your TV via a fully-wired 21-pin SCART cable ( pg. 17), the following functions are available. You can use these functions only with a TV offering T-V Link, etc.* For details, refer to the instruction manual of your TV.

*Compatible with TVs offering T-V Link, EasyLink, Megalogic, SMARTLINK, Q-Link or DATA LOGIC via a fully-wired 21-pin SCART cable. The degree of compatibility and available functions may differ by system.

TV Auto Power On

The TV will turn on and be set to its AV mode automatically whenever you start playback.

For details, refer to the instruction manual of your TV.

Unit Auto Standby

You can use your TV’s remote control to turn off the unit. For details, refer to the instruction manual of your TV.

Direct Rec

You can easily start recording the programme that you are watching on your TV. When you use this function, set “DIRECT REC” to “ON”. ( pg. 68)