JVC LPT0923-001A manual Mode Set, Press rt to select Audio, REC, then press Enter

DVD VIDEO SET UP HDD/DVD SET UP FUNCTION SET UP INITIAL SET UP

Mode Set

SUBSIDIARY SETTINGS EN 67

* The boldface settings below indicate the settings at your purchase.

AUDIO OUTPUT

●Turn on the unit.

●Turn on the TV and select the AV mode.

●Slide the TV/CABLE/SAT/DVD switch to DVD.

CABLE/SAT

TVDVD

8DIGITAL AUDIO OUT — DOLBY DIGITAL/PCM / STREAM/

PCM / PCM ONLY

Set to the appropriate mode according to the type of the device connected to DIGITAL OUT connector.

DOLBY DIGITAL/PCM: Select this when you connect the digital input connector of a Dolby Digital decoder or an amplifier with a built-in Dolby Digital decoder.

STREAM/PCM: Select this when you connect the digital input connector of an amplifier with a built-in DTS, Dolby Digital, or MPEG multichannel decoder.

PCM ONLY: Select this when you connect the linear PCM digital input of other audio equipment (amplifier, MD or DAT deck, etc.).

ENTER

rtwe

SET UP

8ANALOG AUDIO OUT — STEREO / DOLBY SURROUND

Select the appropriate setting to accommodate the unit to the connected A/V equipment. This function takes effect when a DVD VIDEO disc is played back.

STEREO: Select this when listening to conventional two-channel stereo audio with the unit’s AUDIO OUT connectors connected to a stereo amplifier/receiver or TV set, or in case you want to record the audio from a DVD VIDEO disc to a Mini Disc, etc.

DOLBY SURROUND: Select this when listening to multichannel surround audio with the unit’s AUDIO OUT connectors connected to an amplifier/receiver with a built-in surround decoder or a surround decoder.

Various modes of this unit are categorized into menus nested in 2 levels shown in the following table. To change the settings of these modes, find the desired mode in the menu (for details on each menu, see pages 67 through 68), then follow the procedure below.

DVD VIDEO SET UP	LANGUAGE SET ( pg. 21)
	AUDIO OUTPUT ( pg. 67)
	PARENTAL LOCK ( pg. 34)
	DISC PLAY SET UP ( pg. 68)
HDD/DVD SET UP	HDD SET UP ( pg. 68)
	DVD SET UP ( pg. 68)
	DISC SET UP ( pg. 74, 75)
FUNCTION SET UP	REC/PLAY SET UP ( pg. 68)
	DISPLAY SET ( pg. 69)
	VIDEO IN/OUT ( pg. 22, 61)
INITIAL SET UP	TUNER SET ( pg. 70)
	CLOCK SET ( pg. 73)

●The procedure below shows how to set the desired option of the “AUDIO REC” mode as an example.

1 Press SET UP to access the Main Menu screen.

2Press w e to select “FUNCTION SET UP”, then press t.

3Press w e to select “REC/PLAY

SET UP”, then press t.	REC/PLAY SETUP		DISPLAY SET	VIDEO IN/OUT
4 Press rt to select “AUDIO
		XP MODE REC AUDIO			DOLBY DIGITAL
REC”, then press ENTER.		AUDIO REC			NICAM
		DIRECT REC			OFF
5 Press rt to select the desired
		INPUT COLOUR SYSTEM
					PAL
option, then press ENTER.		JUMP TIME
					15 MIN

6 Press SET UP to complete the	SET UP	ENTER	SELECT WITH [	] THEN PRESS [ENTER]
	EXIT	SELECT	PRESS [SET UP] TO EXIT

8D. RANGE CONTROL — NORMAL / WIDE RANGE /

TV MODE

The dynamic range (the difference between the loudest sound and the quietest one) can be compressed during playback of a programme encoded in Dolby Digital format.

This function takes effect when a DVD VIDEO disc recorded in Dolby Digital format is played back at low or middle volume.

NORMAL: Normally select this setting to activate this function.

WIDE RANGE: Select this to deactivate this function when you enjoy wide dynamic range programme.

TV MODE: Select this when you hear the sound through the TV’s speaker(s).

NOTES:

●This function takes no effect on programmes other than that recorded in Dolby Digital format.

●This function dose not work when Simulated Surround Effect is activated. ( pg. 32)

●The effect of “NORMAL” and “WIDE RANGE” may not be different depending on discs.

8OUTPUT LEVEL — STANDARD / LOW

You can lower the output level of analog audio to accommodate the unit to the connected A/V equipment.

STANDARD: Normally select this setting.

LOW: The output level of analog audio is lowered.

setting.