48 EN TIMER RECORDING
|
| Automatic Satellite Programme |
| DECODER connector. |
|
|
|
| ● Make sure the satellite receiver is connected to the unit’s |
|
| Recording |
| ● Programme the timer on the satellite receiver. |
|
|
| ● Slide the TV/CABLE/SAT/DVD switch to DVD. | |
|
|
|
| 1 Press HDD or DVD to choose the recording deck. |
This function allows you to automatically record a satellite |
| |||
programme which is |
| 2 Set | ||
receiver. Connect a satellite receiver to the unit’s |
| |||
| ( pg. 61) | |||
DECODER connector and programme the timer on the satellite |
| |||
| ● Also refer to “IMPORTANT” on page 65. | |||
receiver. The unit starts or stops recording by the signals input |
| |||
| 3 Press REC MODE repeatedly to set the recording mode. | |||
from the satellite receiver. After recording, the unit’s power shuts |
| |||
off automatically. | # | |||
|
|
|
| 4 Press and hold SAT for about 2 seconds to engage the |
|
|
|
| Automatic Satellite Programme Recording mode. “SAT#” appears |
ATTENTION: |
| on the front display panel. | ||
● Be sure not to turn on the satellite receiver before the programme |
| NOTES: | ||
|
| is executed; otherwise, the unit will start recording when the |
| |
|
|
| ● To disengage the Automatic Satellite Programme Recording mode, | |
|
| satellite receiver’s power is turned on. |
| |
|
|
| press SAT#. | |
● If you have connected another appliance other than a satellite |
| |||
| ● If the unit’s power is off, it is not possible to engage the Automatic | |||
|
| receiver to the |
| |
|
|
| Satellite Programme Recording mode. | |
|
| the Automatic Satellite Programme Recording mode; otherwise, |
| |
|
|
| ● In step 4, if “SAT#” blinks quickly on the front display panel even | |
|
| the unit will start recording when the connected appliance’s power |
| |
|
|
| though your satellite receiver’s power is off, Automatic Satellite | |
|
| is turned on. |
| |
|
|
| Programme Recording will not work properly with that satellite | |
● Automatic Satellite Programme Recording and |
| |||
| receiver*. If this is the case, perform “Manual Timer Programming” | |||
|
| cannot be done at the same time. |
| |
|
|
| ( pg. 46) to | |
|
|
|
| |
|
| HDD DVD |
| * Some satellite receivers output signals even if the power is off. |
|
|
| Automatic Satellite Programme Recording is not possible with those | |
|
|
|
| |
|
|
|
| satellite receivers. |
CABLE/SAT
TVDVD
HDD DVD
●“SAT#” blinks on the front display panel while Automatic Satellite Programme Recording is in progress.
●For timer programming of the satellite receiver, refer to the instruction manual of the satellite receiver.
●Automatic Satellite Programme Recording is not possible if your satellite receiver does not have a timer.
●Pressing the unit’s 1 button while Automatic Satellite Programme Recording is in progress turns off the unit’s power and disengages the Automatic Satellite Programme Recording mode.
●If there are more than one satellite programmes you wish to record with Automatic Satellite Programme Recording, it is not possible to set different recording modes for each programme.
●Depending on the type of satellite receiver, the unit may not record a slight portion of the beginning of the programme or may record slightly longer than the actual length of the programme.
●If you engage the Automatic Satellite Programme Recording mode when the satellite receiver’s power is on, the unit will not start Automatic Satellite Programme Recording even though “SAT#” blinks on the front display panel. When the satellite receiver shuts off once and is turned back on again, the unit starts recording.
●You can also record a programme from your cable system in the same way if the system has a timer.
●Just Clock ( pg. 73) does not work when the Automatic Satellite Programme Recording mode is engaged.
REC MODE
SAT#