JVC DR-MH30S, DR-MH20S manual DV Dubbing, When you dub from DV equipment other than a camcorder

60 EN EDITING

	DV Dubbing	8 Locate the point from where you want to start dubbing, then
		stop or pause playback by pressing the following buttons on the
		remote control: 4, 5, 3, 8, 9
You can dub programs from a camcorder or DV equipment
		● To play back in slow speed (1/10 of the normal speed), press 9 to
connected to the unit with a DV cable. The unit’s remote control		pause playback, then press 3 or 5.
allows you the limited control of the connected camcorder or DV		● To play back frame-by-frame, press 9 to pause playback, then press
equipment functions during dubbing.		9 repeatedly. Each press of 9 advances a frame.
		● To change the playback direction, press 3 or 5.

NOTES:

●Use the DV cable VC-VDV 204U for connection.

●When you connect a PC to the DV IN connector, we do not assure the normal operation of this unit.

Your unit

DV IN connector

9 Press w e to select , then press ENTER. The dubbing starts.

●Playback on the external DV equipment and recording on the unit should start simultaneously.

●To pause dubbing, press w e to select , then press ENTER. Both the unit and the external DV equipment pause dubbing. Pressing 9 on the unit also works the same way.

10Press w e to select , then press ENTER. Then press 8. The DV equipment stops.

11Press w e to select , then press ENTER.

12Press 8 twice on the remote control to stop dubbing.

●Both the unit and the external DV equipment stop dubbing.

NOTES:

Camcorder

DV equipment

DV cable (VC-VDV 204U)

(not provided)

DV connector

●Dubbing copyright guarded programs is not possible.

●Original DV informations such as the recording date and time are not recorded.

●The superimposed indication during the operation or dubbing is not recorded.

●If the dubbing is paused while the channel is set to “DV”, you cannot switch channels.

When you dub from DV equipment other than a camcorder

APerform step 1 to 4.

BLocate the point from where you want to start dubbing, then stop on the DV equipment.

●If you pause the DV equipment in this step, a few second’s still picture will be recorded at the beginning of the recorded program.

CSet the input mode to “DV INPUT” on the DV equipment.

● If you select an input mode other than “DV INPUT”, unwanted pictures may be recorded at the beginning of the recorded program.

D Perform step 9 to 12.

To skip unwanted part of the source picture

1 Connect a camcorder or DV equipment to the DV IN connector on the unit’s front panel.

2Press HDD.

3Press CH +/– to set the channel to “DV”.

4Press ON SCREEN.

●The on-screen display for DV dubbing appears.

5 Press w e to select , then press ENTER to display the remote icon (facing to the right) for the DV equipment.

Press ENTER to stop both equipment, then press w e to select

.

Locate the point where you want to restart dubbing by pressing 4, 5, or 3, then press 8.

Press w e to select , then press ENTER to restart dubbing.

6 Press w e to select

, then press ENTER repeatedly until the desired sound track appears on the TV screen.

AUDIO 1: Select this to record the original stereo sound played back on the connected DV equipment.

	HDD	0:00	1:00	2:00	DV
				GR-DV3500
FR360	00:00:00. 00			00:00:00. 00	L – R
12bit	DV	JVC	GR-DV3500		SOUND1

DV DV 1 2

AUDIO 2: Select this to record the

dubbed stereo sound played back on the connected DV equipment.

MIX: Select this to record the sound of both “AUDIO 1” and “AUDIO 2”.

●Note that this selection is not available when the source program is recorded in 16BIT (48 kHz) mode.

7 Press REC MODE repeatedly to set the recording mode.