3M S55, X45, X55 manual About the ﬁlter cover for bottom-up use

Page 10

Setting up

About the ﬁlter cover for bottom-up use

WARNING ►Do not replace the ﬁlter cover during use or immediately after use. While the projector connects with a power supply, or the projector is in a high temperature state, handling could cause an electric shock, a ﬁre, a burn and/or malfunction to the projector.Before handling, make sure the power switch is off and the power cord is not plugged in, then wait at least 45 minutes.

When the projector is installed bottom up, please use the accessory ﬁlter cover for bottom-up use. It is higher than usual ﬁlter cover, to keep the space for intake ventilation. Please change in the following procedure.

To remove		To set
	Filter cover	Filter cover for
	Filter cover	bottom-up use
		bottom-up use

Filter cover’s claw

Filter cover’s claw

1. After making sure that the projector is cool adequately, slowly turn the projector so that the lens-side is facing up. Please be careful for a projector

not to fall. While the projector is placed lens-side up, hold the projector.

2. Please unhook the claw of the ﬁlter cover using a minus screwdriver or similar, and remove the ﬁlter cover.

3. Replace the ﬁlter cover for bottom-up use and snap it back into place.

4. Slowly turn the projector so that the top is facing up.

10

Image 10

Contents Thank you for purchasing this projector About this manualTrademark acknowledgment Contents About contents of package Projector Part namesCB/PB CR/PR Remote control Control buttonsSetting up At 43 screen ArrangementAt 169 screen Adjusting the projectors elevator Bottom of the projector Lever Base Front About the ﬁlter cover for bottom-up use Connecting your devices About Plug-and-Play capabilityConnecting to a speaker with ampliﬁer output Connecting to a monitor outputExamples of connection with a computer CR/PR Examples of connection with a VCR/DVD playerCB/PB Connecting power supply Remote control Putting batteriesUsing the remote control Turning on the power Power on/offTurning off the power Operating Adjusting the volumeSelecting an input signal Temporarily muting the sound At a RGB signal Normal  43  Searching an input signalAdjusting the zoom and focus  At a video signal /no signal 43  169  Small At a RGB signal Using the automatic adjustment featureAdjusting the position  At a video signalFreezing the screen Using the magnify featureTemporarily blanking the screen Operating the computer screen Available function Remote control operationUSB mouse and keyboard control Using the menu function Multifunctional settingsEasy Menu Easy Menu Easy Menu Picture Menu GammaColor Temp Picture MenuHigh  Middle  LOW  Custom SecamLOAD1  LOAD2  LOAD3  LOAD4 TV  Film  Turn OFFProgressive SAVE4 SAVE3  SAVE2  SAVE1Over Scan PhaseImage Menu PositionImage Menu Auto AdjustAt a video signal SizeVideo Format Input MenuComponent Frame LockInput Menu InformationNormal  Whisper Setup MenuVolume Normal  Hinvert  Vinvert  H&VINVERTOSD Bright Screen MenuMenu Position BlankMy Screen Screen MenuStart UP My Screen LockNo Input is Detected MessageSync is OUT of Range Search Reset  CancelOption Menu Auto OFFOption Menu ServiceFactory Reset FAN SpeedMaintenance LampCase of replacement by yourself LampAir ﬁlter Air ﬁlter. And then slowly turn the projector bottom upPage Related messages Related messages Message DescriptionRegarding the indicator lamps Regarding the indicator lamps These has not been properly ﬁxed Electrical power cord is not pluggedPower switch is not set to the on position Phenomenon Cases not involving a machine defect ReferencePhenomena that may easily be mistaken for machine defects RGB output SpeciﬁcationRGB input Video input Communication portSpeciﬁcations How to Order Accessories Part NumberNot included with Basic Packet Part Number DN00741 S55/X45/X55OGENG

Related manuals

Manual 96 pages 36.66 Kb