Extron electronic DVS 406 D, DVS 406 A manual Serial Digital Interface SDI Card Installation

Page 53

Serial Digital Interface (SDI) Card Installation

The optional SDI card may be installed in the scaler if it does not already have an input for a serial digital interface signal. We recommend that you send the unit in to Extron for service and updates.

Changes to electronic components must be performed by authorized service personnel only.

Follow these steps to install an SDI card in the DVS 406.

1.Disconnect the AC power cord from the DVS 406 to remove power from the unit. Then disconnect the input/outut cables.

To prevent electric shock, always unplug the DVS 406 scaler from the

AC power source before opening the enclosure.

2.Remove the scaler from the rack or furniture.

3.Remove the cover of the scaler (the top half of the enclosure) by removing the screws, then lifting the cover straight up. See the top cover removal diagram in the “Firmware Upgrade Installation” section.

Do not touch any switches or other electronic components inside the scaler. Doing so could damage the scaler. Electrostatic discharge (ESD) can damage IC chips even though you cannot feel it. You must be electrically grounded before proceeding with any electronic component replacement. A grounding wrist strap is recommended.

4.Locate the SDI card standoff located near the middle rear portion of the main circuit board (looking from above with the front panel nearest to you).

SDI connector opening

SDI card standoff

5.Remove the adhesive SDI cover from the rear SDI connector opening of the scaler and position the SDI card at an angle with the SDI connector protruding from the rear SDI connector opening.

6.The SDI card has a 20-pin socket on the underside which should align with the 20 pins on the main circuit board. Be sure to align the pins properly, in order to prevent bending the pins, before pressing the SDI card firmly in place against the standoff. The mounting hole on the SDI card should now be directly over the standoff.

DVS 406 • Appendix

A-9

Image 53
Contents DVS Consignes de Sécurité Français Safety Instructions EnglishSicherheitsanleitungen Deutsch Instrucciones de seguridad EspañolRear panel audio inputs Rear panel video inputsRear panel video output Rear panel audio outputMain menu Default Cycle menuInput menu Output menuMemory Presets menu Audio Configuration menuAdvanced Configuration menu DVS 406 Quick Start QS-3Executive Mode menu Picture Adjustments menuExit menu QS-4 DVS 406 Quick StartTable of Contents Table of Contents, cont’d One About this Manual What is the DVS 406?About the DVS Controlling the DVS 406 digital video scalerFeatures Features and OptionsIntroduction, cont’d Options and accessoriesInstallation and Operation Mounting the Scaler DVS 406 Installation and OperationTabletop use Rack mountingExtron DVS Application diagramDVS 406 AD rear panel connectors Rear Panel FeaturesOnly DVS 406 D and DVS 406 AD models have an SDI connector Installation and Operation, cont’d Picture adjustment buttons Front Panel FeaturesInput selection buttons Take buttonLCD menu display and controls Setting up a DVD sourceOptimizing the System Menu overview Menus, Configuration, and AdjustmentsMoving through menus by using front panel controls Input Configuration Resolution and refresh rates Output ConfigurationInput Video Type #1 Input Video Type #2 and #3Available Scaler Output Resolutions and Rates 50 Hz Audio Configuration56 Hz 60 Hz 75 Hz Lock @ 50/60 True 72/100 Output Sync RGB formatAudio Level Memory PresetsAudio Switch Recalling a preset Save Save memory presetsClear memory presets Top and bottom blanking blanking adjustment Advanced ConfigurationEffect type Edge smoothingSwitch mode RGB delay Triple-Action SwitchingBlue mode Key modePulldown detection PAL film mode detect Image AdjustmentsReset Exit MenuFront Panel Security Lockout Adjust knobs have no mechanical limits to their rotationSelecting a preset IR 901 Infrared Remote ControlSelecting an input Freezing an inputOperating Problems TroubleshootingDVS 406 Installation and Operation Installation and Operation, cont’d Three RS-232 Programmer’s Guide Error responsesHost-to-scaler communications Scaler-initiated messagesSymbol definitions Using the command/response tablesSerial Communication, cont’d Command Ascii Command Response Additional descriptionTint Top blanking Values Command Ascii Command ResponseControl Software for Windows Installing the softwareUsing the control program Using the help program Serial Communication, cont’d AAppendix DVS 406 Appendix SpecificationsAudio Accessories Part Numbers and AccessoriesAccessories Part number Included partsRemove 13 screws from top and sides Lift Cover Straight Up Firmware Upgrade InstallationU41 Audio card standoffs Audio Card InstallationPin socket on back of audio card Pin connector on main board SDI connector opening SDI card standoff Serial Digital Interface SDI Card InstallationPin socket on back of SDI card Pin connector on main board FCC Class a Notice Extron’s Warranty Extron Electronics, USA