Epson Bocs Program the rest of your remotes for each room, Set the master remote

Page 22

6.Press the Select/OK button to accept the new code.

Step 4: Program the rest of your remotes for each room

This is exactly like step 2 – just grab a new remote, make sure it is Paired to your Xtender, and program it for the TV in the room where you intend to leave that remote.

Step 5: Set the master remote

Note you only need to perform this step if you have connected a TV to the “Local TV” coax connector on the Xtender

The "Local Master" remote is defined as the remote that controls the TV that is connected to the "local TV" coax output from the Xtender. This remote must identify itself to the Xtender so that the Xtender can switch the correct output signal onto the "local TV" output, depending on whether the TV is tuned to a TV channel or a BOCS channels. This switching allows you to watch TV channels that would otherwise be replaced by the BOCS channels. When you press the red, green, or blue button on the "Local Master" remote, the Xtender switches BOCS channels onto the "local TV" coax output. When you press the "Local TV" button, the Xtender changes the switch to output CATV signals to the "local TV" coax output.

To set or remove the remote as a "Local Master"

1.Press and hold one of the following combinations for at least 2 seconds:

"Menu" and "Vol +" to set the remote as local master.

"Menu" and "Vol -" to remove the remote as local master.

2.The Power LED will turn on.

3.Press Select/OK to confirm.

4.If successful, the power LED will pulse twice and turn off. If the function failed, the power LED will pulse rapidly for one second, and then turn off.

That’s it! You are ready to begin using your Xtender system. Enjoy

Programming the Remotes

22

Image 22

Contents Installation Manual Contents Now You Can… ChapterWelcome to the World of Whole-Home Entertainment Choices Without…Tools Xtender Installation KitWhat You Need XtenderRemote Control Lights What’s on the Front Panel? What’s on the Back Panel? What’s on the Remote? Those Needing a Little ExplanationInstallation Overview Easy asMinimum Location Requirements Power the Coax WireSelect Location for the Xtender Likely Locations Choose OneLocate your cable box Find the Powered Cable Locate the SplitterConnecting the SuperCombiner Connect Xtender Installing the XtenderConnect the Audio/Video devices to the Xtender Red Channel Set Up Connect the Device to the XtenderConnect the IR Blaster Green Channel Set UpConnect the A/V Device to the Xtender Checking Power Supply Blue Channel Set UpConnecting Xtender’s Power Supply Optional Connect to the local TVRemote Control Setup for Local TV Pair Remotes Programming the Remotes Three Steps to Programming the Remotes Pick a room, program a remote to work the TV in that roomAlternate Remote programming procedure for TV Auto-Scan Program the Xtender to Control the A/V DevicesEnter the device code press Select/OK to confirm Set the master remote Program the rest of your remotes for each roomTo set or remove the remote as a Local Master Control other devices in the same room as the remote Volume Punch-ThroughMore Programming Options Punch-ThroughLearn IR Codes Channel Punch-ThroughHave the Bocs Remote Learn IR Codes from Another Remote Have the Xtender Learn IR Codes from Another Remote Unlearn IR CodesChannel Tuning Delay Adjust the Video quality of Xtender channels Using the Remotes Programming the Remotes Troubleshooting Programming the Remotes Programming the Remotes Programming the Remotes Programming the Remotes Appendix a Television Device CodesTelevision SVA Plasma TVRCA TMKTV/VCR Combination TV/DVD CombinationTV/VCR/DVD Combination Cable Box Cable & Satellite Box Device CodesAppendix B Satellite BoxDVD Player Video Device CodesAppendix C AMWCCE Laser Disk PlayerABS HI-QDigital Video Recorder DVR Auxiliary Device Codes Home Automation PCSProcedure Remote Control Special Function Quick Reference