Vidikron Vision 30 manual Troubleshooting

Page 49

Troubleshooting

PROBLEM

POSSIBLE CAUSE

REMEDY

The projector does

There is no power from the

Plug the power cord into the

not turn on

power cable.

AC power socket on the rear of

 

 

the projector and an electrical

 

 

outlet.

 

The power switch is not turned

Turn on the power switch.

 

on.

 

 

The projector was turned on

Wait until projector completes

 

again within the cool down

the cool down time.

 

time.

 

 

Lamp cover is not attached

Correctly attach the lamp

 

well.

cover.

No picture

The lamp cover is not correctly

Correctly attach the lamp

 

attached.

cover.

 

The projector is not correctly

Check the connection.

 

connected to the input source

 

 

device.

 

 

The input signal has not been

Select the correct input signal

 

correctly selected.

with the SOURCE input keys: VID,

 

 

S-VID, COMP1, COMP2, RGBHD

 

 

or HDMI.

 

T E M P L E D o r L AM P L E D

Please contact your Vidikron

 

blinking.

dealer for assistance.

Image is unstable

The connection cables are not

Correctly connect the cables to

 

connected to the projector.

the appropriate terminals.

Picture is blurred

The projection lens is not

Adjust the focus of the projection

 

correctly focused.

lens with the focus ring.

 

The projector and the screen are

Adjust the projection angle and

 

not aligned squarely.

direction, and the height of the

 

 

projector.

Remote control

The batteries are exhausted.

Replace both batteries with new

does not work

 

ones.

correctly

 

 

LAMP LED blinks

The cooling fan does not work

Please contact your Vidikron

red

well.

dealer for assistance.

 

The temperature inside the

Check that the ventilation holes

 

projector is extremely high.

are not blocked.

LAMP LED blinks

The lamp has exceed its specified

Replace the lamp with a new

red; POWER LED is

usage hours.

one.

green

The lamp has burned out.

Replace the lamp with a new

 

 

 

one.

Vidikron Vision Model 30 Owner’s Operating Manual

49

Image 49
Contents DLP Projector Page Table of Contents Lamp Replacement Troubleshooting RS-232 Setup Warranty TWO Year Limited WarrantyRIGHTS, Limits and Exclusions Vidikron Safety Precautions Overview Top IR Sensor Status LEDs Exhaust VentIntake Vent Front IR Sensor Vidikron Logo Projection LensAC Power in Socket AC Power Switch Cable Access Door Connector PanelFront / Rear Adjusters Built-in Control PanelThis page is intentionally left blank Control Panel Controls and FunctionsBuilt-In Control Panel Connector PanelEnter Vidikron Logo Remote ControlRemote Control Control Panel Remote Control Functions Compared This page is intentionally left blank About the Remote Control InstallationAbout the Batteries Screen Type and Size Front Screen Installations Installation ConsiderationsScreen size Rear screen installationsInstallation Floor Installation Ceiling InstallationMounting Folded Optics Connections Connecting Video InputsConnections Hdmi Source DVD player or HD tuner with Hdmi or DVI out Connecting an Hdmi DeviceConnecting to AC Power Adjusting the Zoom and Focus Removing the Lens Cap Turning on the PowerAdjusting Projector Height or Projection Angle Basic OperationMemory Selecting an Aspect Selecting VideoRatio Exitmenu Offon Turning off the Power On-Screen Display Menus Picture Quality Adjustments Color Temperature Anamorphic Letterbox Image OptionsStandard 4/3 IntelliWideCinema Fill CinemaHD/RGB Adjust Projector Status Installation InstallationService ServiceEnter On-Screen Display Menus RS-232 Baud Rate ISF Calibration ISF CalibrationISF Enable Lamp Replacement Lamp Replacement Troubleshooting Troubleshooting Connecting RS-232 to the Projector RS-232 SetupRS-232 Pin Assignments Sub 9-pin female Pin RJ-11 Function Code Function RS-232C Control CodesCodes RS-232C ControlThis page is intentionally left blank Horizontal Vertical Offset Lamp Lamp Life Inputs 12V Output SpecificationsDimensions Brightness Contrast Power RequirementsDimensions RUMA-011140