ViewSonic PJD5152, PJD5352 warranty Controls and functions, Projector and remote control

Page 11

Controls and functions

Projector and remote control

1

2

3

4

5

6

7

8

6

14

5

15

9

16

10 17

11

12 18

13 19

20

10

21

13

22

23

24

25

1.Focus ring

Adjusts the focus of the projected image. See "Fine-tuning the image size and clarity" on page 26 for details.

2.Zoom ring

Adjusts the size of the image. See "Fine- tuning the image size and clarity" on page 26 for details.

3.TEMPerature indicator light

Lights up red if the projector's temperature becomes too high. See "Indicators" on page 49 for details.

4.POWER indicator light

Lights up or flashes when the projector is under operation. See "Indicators" on page 49 for details.

5. II POWER

Toggles the projector between standby mode and on. See "Starting up the projector" on page 19 and "Shutting down the projector" on page 35 for details.

6.Keystone/Arrow keys ( / Up, /

Down)

Manually corrects distorted images resulting from an angled projection. See "Correcting keystone" on page 26 for details.

7. Left/Blank

Hides the screen picture. See "Hiding the image" on page 33 for details.

8.MENU/EXIT

Turns on the On-Screen Display (OSD) menu. Goes back to previous OSD menu, exits and saves menu settings. See "Using the menus" on page 21 for details.

8 Introduction

Image 11
Contents ViewSonic Compliance Information Hexavalent Chromium Cr6+ Polybrominated biphenyls PBB SubstanceActual Concentration Lead Pb Mercury Hg Cadmium CdCopyright Information Table of contents Important safety instructions Safety InstructionsSafety instructions for ceiling mounting of the projector Introduction Projector featuresIntroduction Shipping contents Projector exterior view Controls and functions Projector and remote controlAuto Lamp indicator lightColor Mode Volume keys +Pull out the battery holder Remote control effective rangeChoosing a location Positioning your projectorScreen Center of lens Projection dimensionsTo connect the projector to a notebook or desktop computer Connecting a computer or monitorConnecting a computer ConnectionMonitor Computer VGA to DVI Cable VGA cable Connecting a monitorTo connect the projector to a monitor Better video quality Connecting Video source devicesConnecting audio Best video qualityTo connect the projector to a Component Video source device Connecting a Component Video source deviceAV device Speakers Audio cable Video cable Cable Connecting an S-Video source deviceTo connect the projector to an S-Video source device Speakers AV device Video cable Audio cable Cable Connecting a composite Video source deviceTo connect the projector to a composite Video source device Operation OperationStarting up the projector See Timing chart on page 52 for details System Setup Advanced Using the menusUse / to highlight the System Setup Basic menu System Setup BasicNew password Utilizing the password functionSetting a password If you forget the passwordDisabling the password function Entering the password recall procedureChanging the password Switching input signal Auto-adjusting the image Adjusting the projected imageAdjusting the projection angle MODE/ENTER on the projector or Enter Fine-tuning the image size and clarityOn the remote control. The Keystone Correcting keystoneSelecting the aspect ratio Magnifying and searching for detailsAbout the aspect ratio Video input signals S-Video, Video, D-Sub / Comp /2 YPbPr Selecting a picture modePicture modes for different types of signals PC input signals D-Sub / Comp /2 analog RGBAdjusting Brightness Using Screen ColorFine-tuning the image quality in user modes Setting the User 1/User 2 modeAdjusting Brilliant Color Adjusting ColorAdjusting Tint Adjusting SharpnessColor Management To adjust the settingsOrder to draw the audiences full attention to Hiding the imageLocking control keys Press MENU/EXIT on the projector or Menu To activate the High Altitude ModeFreezing the image Operating in a high altitude environmentShutting down the projector Personalizing the projector menu displayMain menu Sub-menu Options Menu operationMenu system Advanced BasicDescription of each menu Mode Color ModeSettings ReferenceProjector Auto PowerBlank Timer TimerMenu System Setup Advanced menu Function Description Active VGAOut AudioCurrent Advanced Settings Reset AllLamp SecurityCare of the projector MaintenanceGetting to know the lamp hour Setting Lamp mode as EconomicSetting Auto Power Off Lamp informationStatus Message Timing of replacing the lampLoosen the screw that secures the lamp Replacing the lampType number RLC-055 Maintenance Restart the projector Resetting the lamp timerTighten the screw that secures the lamp Lamp events IndicatorsPower events Light Status & DescriptionCause Remedy TroubleshootingProjector specifications SpecificationsTiming chart DimensionsCeiling mount installation Horizontal Signal Format Horizontal Frequency kHz Vertical Frequency HzCopyright information Copyright informationPin assignment for this two end RS232 command tableAppendix IR control tableData Length Bit Parity Check None Stop Bit InterfaceRS-232 protocol Baud RateContrast Write Blank on 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x09 0x01 VGA Hour Customer Support Limited Warranty PRJLW01 Rev h How to get serviceViewsonic Projector Mexico Limited WarrantyNúmero Gratis DE Asistencia Técnica Para Todo México