ViewSonic PJD5152, PJD5352 warranty Troubleshooting, Cause Remedy

Page 53

Troubleshooting

The projector does not turn on.

Cause

Remedy

 

 

 

Plug the power cord into the AC inlet on the

There is no power from the power

projector, and plug the power cord into the

cord.

power outlet. If the power outlet has a switch,

 

make sure that it is switched on.

 

 

Attempting to turn the projector on

Wait until the cooling down process has

again during the cooling process.

completed.

 

 

No picture

 

 

 

Cause

Remedy

 

 

The video source is not turned on or

Turn the video source on and check that the

connected correctly.

signal cable is connected correctly.

 

 

The projector is not correctly

Check the connection.

connected to the input signal device.

 

 

 

The input signal has not been

Select the correct input signal with the

SOURCE key on the projector or remote

correctly selected.

control.

 

 

 

The lens cover is still closed.

Open the lens cover.

 

 

Blurred image

 

 

 

Cause

Remedy

 

 

The projection lens is not correctly

Adjust the focus of the lens using the focus

focused.

ring.

 

 

The projector and the screen are not

Adjust the projection angle and direction as

aligned properly.

well as the height of the projector if necessary.

 

 

The lens cover is still closed.

Open the lens cover.

Remote control does not work

 

 

 

Cause

Remedy

 

 

The battery is out of power.

Replace the battery with a new one.

There is an obstacle between the

Remove the obstacle.

remote control and the projector.

 

 

 

You are too far away from the

Stand within 8 meters (26 feet) of the

projector.

projector.

 

 

50 Troubleshooting

Page 52 Page 54
Image 53
Page 52 Page 54
Contents ViewSonic Compliance Information Actual Concentration SubstanceLead Pb Mercury Hg Cadmium Cd Hexavalent Chromium Cr6+ Polybrominated biphenyls PBBCopyright Information Table of contents Important safety instructions Safety InstructionsSafety instructions for ceiling mounting of the projector Introduction Projector featuresIntroduction Shipping contents Projector exterior view Controls and functions Projector and remote controlColor Mode Lamp indicator lightVolume keys + AutoPull out the battery holder Remote control effective rangeChoosing a location Positioning your projectorScreen Center of lens Projection dimensionsConnecting a computer Connecting a computer or monitorConnection To connect the projector to a notebook or desktop computerMonitor Computer VGA to DVI Cable VGA cable Connecting a monitorTo connect the projector to a monitor Connecting audio Connecting Video source devicesBest video quality Better video qualityTo connect the projector to a Component Video source device Connecting a Component Video source deviceAV device Speakers Audio cable Video cable Cable Connecting an S-Video source deviceTo connect the projector to an S-Video source device Speakers AV device Video cable Audio cable Cable Connecting a composite Video source deviceTo connect the projector to a composite Video source device Operation OperationStarting up the projector See Timing chart on page 52 for details Use / to highlight the System Setup Basic menu Using the menusSystem Setup Basic System Setup AdvancedSetting a password Utilizing the password functionIf you forget the password New passwordDisabling the password function Entering the password recall procedureChanging the password Switching input signal Auto-adjusting the image Adjusting the projected imageAdjusting the projection angle On the remote control. The Keystone Fine-tuning the image size and clarityCorrecting keystone MODE/ENTER on the projector or EnterSelecting the aspect ratio Magnifying and searching for detailsAbout the aspect ratio Picture modes for different types of signals Selecting a picture modePC input signals D-Sub / Comp /2 analog RGB Video input signals S-Video, Video, D-Sub / Comp /2 YPbPrFine-tuning the image quality in user modes Using Screen ColorSetting the User 1/User 2 mode Adjusting BrightnessAdjusting Tint Adjusting ColorAdjusting Sharpness Adjusting Brilliant ColorColor Management To adjust the settingsOrder to draw the audiences full attention to Hiding the imageLocking control keys Freezing the image To activate the High Altitude ModeOperating in a high altitude environment Press MENU/EXIT on the projector or MenuShutting down the projector Personalizing the projector menu displayMain menu Sub-menu Options Menu operationMenu system Advanced BasicDescription of each menu Settings Color ModeReference ModeBlank Timer Auto PowerTimer ProjectorOut System Setup Advanced menu Function Description Active VGAAudio MenuLamp Advanced Settings Reset AllSecurity CurrentCare of the projector MaintenanceSetting Auto Power Off Setting Lamp mode as EconomicLamp information Getting to know the lamp hourStatus Message Timing of replacing the lampLoosen the screw that secures the lamp Replacing the lampType number RLC-055 Maintenance Restart the projector Resetting the lamp timerTighten the screw that secures the lamp Power events IndicatorsLight Status & Description Lamp eventsCause Remedy TroubleshootingProjector specifications SpecificationsTiming chart DimensionsCeiling mount installation Horizontal Signal Format Horizontal Frequency kHz Vertical Frequency HzCopyright information Copyright informationAppendix RS232 command tableIR control table Pin assignment for this two endRS-232 protocol InterfaceBaud Rate Data Length Bit Parity Check None Stop BitContrast Write Blank on 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x09 0x01 VGA Hour Customer Support Limited Warranty PRJLW01 Rev h How to get serviceViewsonic Projector Mexico Limited WarrantyNúmero Gratis DE Asistencia Técnica Para Todo México
Top Page Image Contents