ViewSonic PJD5152, PJD5352 warranty Remote control effective range, Pull out the battery holder

Page 13

Remote control effective range

Infra-Red (IR) remote control sensor is located on the front of the projector. The remote control must be held at an angle within 30 degrees perpendicular to the projector's IR remote control sensor to function correctly. The distance between the remote control and the sensor should not exceed 8 meters (~ 26 feet).

Make sure that there are no obstacles between the remote control and the IR sensor on the projector that might obstruct the infra-red beam.

Replacing the remote control battery

1.Pull out the battery holder.

Please follow the illustrated instructions. Push and hold the locking arm while pulling out the battery holder.

2.Insert the new battery in the holder. Note the positive polarity should face outward.

3.Push the holder into the remote control.

1 2

CAUTION

Avoid excessive heat and humidity.

There may be battery damage if the battery is incorrectly replaced.

Replace only with the same or equivalent type recommended by the battery manufacturer.

Dispose of the used battery according to the battery manufacturer’s instructions.

Never throw a battery into a fire. There may be danger of an explosion.

If the battery is dead or if you will not be using the remote control for a long time, remove the battery to prevent damage to the remote control from possible battery leakage.

10 Introduction

Image 13
Contents ViewSonic Compliance Information Actual Concentration SubstanceLead Pb Mercury Hg Cadmium Cd Hexavalent Chromium Cr6+ Polybrominated biphenyls PBBCopyright Information Table of contents Important safety instructions Safety InstructionsSafety instructions for ceiling mounting of the projector Introduction Projector featuresIntroduction Shipping contents Projector exterior view Controls and functions Projector and remote controlColor Mode Lamp indicator lightVolume keys + AutoPull out the battery holder Remote control effective rangeChoosing a location Positioning your projectorScreen Center of lens Projection dimensionsConnecting a computer Connecting a computer or monitorConnection To connect the projector to a notebook or desktop computerTo connect the projector to a monitor Connecting a monitorMonitor Computer VGA to DVI Cable VGA cable Connecting audio Connecting Video source devicesBest video quality Better video qualityTo connect the projector to a Component Video source device Connecting a Component Video source deviceTo connect the projector to an S-Video source device Connecting an S-Video source deviceAV device Speakers Audio cable Video cable Cable To connect the projector to a composite Video source device Connecting a composite Video source deviceSpeakers AV device Video cable Audio cable Cable Starting up the projector OperationOperation See Timing chart on page 52 for details Use / to highlight the System Setup Basic menu Using the menusSystem Setup Basic System Setup AdvancedSetting a password Utilizing the password functionIf you forget the password New passwordChanging the password Entering the password recall procedureDisabling the password function Switching input signal Adjusting the projection angle Adjusting the projected imageAuto-adjusting the image On the remote control. The Keystone Fine-tuning the image size and clarityCorrecting keystone MODE/ENTER on the projector or EnterSelecting the aspect ratio Magnifying and searching for detailsAbout the aspect ratio Picture modes for different types of signals Selecting a picture modePC input signals D-Sub / Comp /2 analog RGB Video input signals S-Video, Video, D-Sub / Comp /2 YPbPrFine-tuning the image quality in user modes Using Screen ColorSetting the User 1/User 2 mode Adjusting BrightnessAdjusting Tint Adjusting ColorAdjusting Sharpness Adjusting Brilliant ColorColor Management To adjust the settingsLocking control keys Hiding the imageOrder to draw the audiences full attention to Freezing the image To activate the High Altitude ModeOperating in a high altitude environment Press MENU/EXIT on the projector or MenuShutting down the projector Personalizing the projector menu displayMenu system Menu operationMain menu Sub-menu Options Advanced BasicDescription of each menu Settings Color ModeReference ModeBlank Timer Auto PowerTimer ProjectorOut System Setup Advanced menu Function Description Active VGAAudio MenuLamp Advanced Settings Reset AllSecurity CurrentCare of the projector MaintenanceSetting Auto Power Off Setting Lamp mode as EconomicLamp information Getting to know the lamp hourStatus Message Timing of replacing the lampType number RLC-055 Replacing the lampLoosen the screw that secures the lamp Maintenance Tighten the screw that secures the lamp Resetting the lamp timerRestart the projector Power events IndicatorsLight Status & Description Lamp eventsCause Remedy TroubleshootingProjector specifications SpecificationsCeiling mount installation DimensionsTiming chart Horizontal Signal Format Horizontal Frequency kHz Vertical Frequency HzCopyright information Copyright informationAppendix RS232 command tableIR control table Pin assignment for this two endRS-232 protocol InterfaceBaud Rate Data Length Bit Parity Check None Stop BitContrast Write Blank on 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x09 0x01 VGA Hour Customer Support Limited Warranty PRJLW01 Rev h How to get serviceViewsonic Projector Mexico Limited WarrantyNúmero Gratis DE Asistencia Técnica Para Todo México