ViewSonic PJD5352 System Setup Advanced menu Function Description Active VGA, Out, Audio, Menu

Page 44

5. SYSTEM SETUP: Advanced menu

Function

Description

Active VGA

Selecting On outputs a VGA signal when the COMPUTER IN

1/COMPUTER IN 2 and COMPUTER OUT sockets are

Out

correctly connected to devices. See "Connecting a monitor" on

 

page 14 for how to make the connection.

 

The sound adjustments made as below will have an effect on the

 

projector speaker. Be sure you have made a correct connection to

 

the projector audio input. See "Connection" on page 13 for how

 

the audio input is connected.

Audio

Mute

Mutes the sound.

Settings

Volume

 

 

Adjusts the sound level

 

Active Audio Out

 

Selecting On outputs an audio signal when the AUDIO IN and

 

AUDIO OUT sockets are correctly connected to devices.

 

Menu Display Time

Menu

Sets the length of time the OSD will remain active after your last

key press. The range is from 5 to 30 seconds in 5-second

Settings

increments.

Menu Position

 

 

Sets the On-Screen Display (OSD) menu position.

 

 

 

Closed Caption Enable

 

Activates the function by selecting On when the selected input

 

signal carries closed captions.

 

• Captions: An on-screen display of the dialogue, narration,

 

and sound effects of TV programs and videos that are closed

 

captioned (usually marked as "CC" in TV listings).

Closed

Set your screen aspect ratio to 4:3. This function is not

Caption

available when the aspect ratio is “16:9”.

This function is only available when a Composite video or

 

 

S-Video input signal is selected and its system format is

 

NTSC.

 

Caption Version

 

Selects a preferred closed captioning mode. To view captions,

 

select CC1, CC2, CC3, or CC4 (CC1 displays captions in the

 

primary language in your area).

 

 

Operation 41

Image 44
Contents ViewSonic Compliance Information Substance Actual ConcentrationLead Pb Mercury Hg Cadmium Cd Hexavalent Chromium Cr6+ Polybrominated biphenyls PBBCopyright Information Table of contents Safety Instructions Important safety instructionsSafety instructions for ceiling mounting of the projector Introduction Projector featuresIntroduction Shipping contents Projector exterior view Projector and remote control Controls and functionsLamp indicator light Color ModeVolume keys + AutoRemote control effective range Pull out the battery holderPositioning your projector Choosing a locationProjection dimensions Screen Center of lensConnecting a computer or monitor Connecting a computerConnection To connect the projector to a notebook or desktop computerMonitor Computer VGA to DVI Cable VGA cable Connecting a monitorTo connect the projector to a monitor Connecting Video source devices Connecting audioBest video quality Better video qualityConnecting a Component Video source device To connect the projector to a Component Video source deviceAV device Speakers Audio cable Video cable Cable Connecting an S-Video source deviceTo connect the projector to an S-Video source device Speakers AV device Video cable Audio cable Cable Connecting a composite Video source deviceTo connect the projector to a composite Video source device Operation OperationStarting up the projector See Timing chart on page 52 for details Using the menus Use / to highlight the System Setup Basic menuSystem Setup Basic System Setup AdvancedUtilizing the password function Setting a passwordIf you forget the password New passwordDisabling the password function Entering the password recall procedureChanging the password Switching input signal Auto-adjusting the image Adjusting the projected imageAdjusting the projection angle Fine-tuning the image size and clarity On the remote control. The KeystoneCorrecting keystone MODE/ENTER on the projector or EnterMagnifying and searching for details Selecting the aspect ratioAbout the aspect ratio Selecting a picture mode Picture modes for different types of signalsPC input signals D-Sub / Comp /2 analog RGB Video input signals S-Video, Video, D-Sub / Comp /2 YPbPrUsing Screen Color Fine-tuning the image quality in user modesSetting the User 1/User 2 mode Adjusting BrightnessAdjusting Color Adjusting TintAdjusting Sharpness Adjusting Brilliant ColorTo adjust the settings Color ManagementOrder to draw the audiences full attention to Hiding the imageLocking control keys To activate the High Altitude Mode Freezing the imageOperating in a high altitude environment Press MENU/EXIT on the projector or MenuPersonalizing the projector menu display Shutting down the projectorMain menu Sub-menu Options Menu operationMenu system Basic AdvancedDescription of each menu Color Mode SettingsReference ModeAuto Power Blank TimerTimer ProjectorSystem Setup Advanced menu Function Description Active VGA OutAudio MenuAdvanced Settings Reset All LampSecurity CurrentMaintenance Care of the projectorSetting Lamp mode as Economic Setting Auto Power OffLamp information Getting to know the lamp hourTiming of replacing the lamp Status MessageLoosen the screw that secures the lamp Replacing the lampType number RLC-055 Maintenance Restart the projector Resetting the lamp timerTighten the screw that secures the lamp Indicators Power eventsLight Status & Description Lamp eventsTroubleshooting Cause RemedySpecifications Projector specificationsTiming chart DimensionsCeiling mount installation Signal Format Horizontal Frequency kHz Vertical Frequency Hz HorizontalCopyright information Copyright informationRS232 command table AppendixIR control table Pin assignment for this two endInterface RS-232 protocolBaud Rate Data Length Bit Parity Check None Stop BitContrast Write Blank on 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x09 0x01 VGA Hour Customer Support Limited Warranty How to get service PRJLW01 Rev hMexico Limited Warranty Viewsonic ProjectorNúmero Gratis DE Asistencia Técnica Para Todo México