ViewSonic PJD5352, PJD5152 warranty Adjusting the projected image, Adjusting the projection angle

Page 28

Adjusting the projected image

Adjusting the projection angle

The projector is equipped with 1 quick-release adjuster foot and 1 rear adjuster foot. These adjusters change the image height and projection angle. To adjust the projector:

1.Press the quick-release button and lift the

front of the projector. Once the image is positioned where you want it, release the quick-release button to lock the foot in

 

position.

 

 

2.

Screw the rear adjuster foot to fine tune the

 

 

 

horizontal angle.

2

1

To retract the foot, hold up the projector while pressing the quick-release button, then slowly lower the projector. Screw the rear adjuster foot in a reverse direction.

If the projector is not placed on a flat surface or the screen and the projector are not perpendicular to each other, the projected image becomes trapezoidal. To correct this situation, see "Correcting keystone" on page 26 for details.

Do not look into the lens while the lamp is on. The strong light from the lamp may cause damage to your eyes.

Be careful when you press the adjuster button as it is close to the exhaust vent where hot air comes from.

Auto-adjusting the image

In some cases, you may need to optimize the picture quality. To do this, press AUTO on the projector or remote control. Within 3 seconds, the built-in Intelligent Auto Adjustment function will re-adjust the values of Frequency and Clock to provide the best picture quality.

The current source information will be displayed in the upper left corner of the screen for 3 seconds.

The screen will be blank while AUTO is functioning.

This function is only available when PC signal (analog RGB) is selected.

Operation 25

Image 28
Contents ViewSonic Compliance Information Substance Actual ConcentrationLead Pb Mercury Hg Cadmium Cd Hexavalent Chromium Cr6+ Polybrominated biphenyls PBBCopyright Information Table of contents Safety Instructions Important safety instructionsSafety instructions for ceiling mounting of the projector Introduction Projector featuresIntroduction Shipping contents Projector exterior view Projector and remote control Controls and functionsLamp indicator light Color ModeVolume keys + AutoRemote control effective range Pull out the battery holderPositioning your projector Choosing a locationProjection dimensions Screen Center of lensConnecting a computer or monitor Connecting a computerConnection To connect the projector to a notebook or desktop computerTo connect the projector to a monitor Connecting a monitorMonitor Computer VGA to DVI Cable VGA cable Connecting Video source devices Connecting audioBest video quality Better video qualityConnecting a Component Video source device To connect the projector to a Component Video source deviceTo connect the projector to an S-Video source device Connecting an S-Video source deviceAV device Speakers Audio cable Video cable Cable To connect the projector to a composite Video source device Connecting a composite Video source deviceSpeakers AV device Video cable Audio cable Cable Starting up the projector OperationOperation See Timing chart on page 52 for details Using the menus Use / to highlight the System Setup Basic menuSystem Setup Basic System Setup AdvancedUtilizing the password function Setting a passwordIf you forget the password New passwordChanging the password Entering the password recall procedureDisabling the password function Switching input signal Adjusting the projection angle Adjusting the projected imageAuto-adjusting the image Fine-tuning the image size and clarity On the remote control. The KeystoneCorrecting keystone MODE/ENTER on the projector or EnterMagnifying and searching for details Selecting the aspect ratioAbout the aspect ratio Selecting a picture mode Picture modes for different types of signalsPC input signals D-Sub / Comp /2 analog RGB Video input signals S-Video, Video, D-Sub / Comp /2 YPbPrUsing Screen Color Fine-tuning the image quality in user modesSetting the User 1/User 2 mode Adjusting BrightnessAdjusting Color Adjusting TintAdjusting Sharpness Adjusting Brilliant ColorTo adjust the settings Color ManagementLocking control keys Hiding the imageOrder to draw the audiences full attention to To activate the High Altitude Mode Freezing the imageOperating in a high altitude environment Press MENU/EXIT on the projector or MenuPersonalizing the projector menu display Shutting down the projectorMenu system Menu operationMain menu Sub-menu Options Basic AdvancedDescription of each menu Color Mode SettingsReference ModeAuto Power Blank TimerTimer ProjectorSystem Setup Advanced menu Function Description Active VGA OutAudio MenuAdvanced Settings Reset All LampSecurity CurrentMaintenance Care of the projectorSetting Lamp mode as Economic Setting Auto Power OffLamp information Getting to know the lamp hourTiming of replacing the lamp Status MessageType number RLC-055 Replacing the lampLoosen the screw that secures the lamp Maintenance Tighten the screw that secures the lamp Resetting the lamp timerRestart the projector Indicators Power eventsLight Status & Description Lamp eventsTroubleshooting Cause RemedySpecifications Projector specificationsCeiling mount installation DimensionsTiming chart Signal Format Horizontal Frequency kHz Vertical Frequency Hz HorizontalCopyright information Copyright informationRS232 command table AppendixIR control table Pin assignment for this two endInterface RS-232 protocolBaud Rate Data Length Bit Parity Check None Stop BitContrast Write Blank on 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x09 0x01 VGA Hour Customer Support Limited Warranty How to get service PRJLW01 Rev hMexico Limited Warranty Viewsonic ProjectorNúmero Gratis DE Asistencia Técnica Para Todo México