ViewSonic PJD5352, PJD5152 warranty Connection, Connecting a computer or monitor

Page 16

Connection

When connecting a signal source to the projector, be sure to:

1.Turn all equipment off before making any connections.

2.Use the correct signal cables for each source.

3.Ensure the cables are firmly inserted.

In the connections shown below, some cables may not be included with the projector (see "Shipping contents" on page 6). They are commercially available from electronics stores.

Connecting a computer or monitor

Connecting a computer

The projector provides two VGA input sockets that allow you to connect them to both IBM® compatibles and Macintosh® computers. A Mac adapter is needed if you are connecting legacy version Macintosh computers.

To connect the projector to a notebook or desktop computer:

1.Take the supplied VGA cable and connect one end to the D-Sub output socket of the computer.

2.Connect the other end of the VGA cable to the COMPUTER IN 1 or COMPUTER IN 2 signal input socket on the projector.

3.If you wish to make use of the projector (mixed mono) speaker in your presentations, take a suitable audio cable and connect one end of the cable to the audio output socket of the device, and the other end to the AUDIO IN socket of the projector.

4.If you wish, you can use another suitable audio cable and connect one end of the cable to the AUDIO OUT socket of the projector, and the other end to your external speakers (not supplied).

Once connected, the audio can be controlled by the projector On-Screen Display (OSD) menus.

The final connection path should be like that shown in the following diagram:

Notebook or desktop computer

Speakers

or

 

VGA cable

Audio

Audio cable

cable

Connection 13

Image 16
Contents ViewSonic Compliance Information Substance Actual ConcentrationLead Pb Mercury Hg Cadmium Cd Hexavalent Chromium Cr6+ Polybrominated biphenyls PBBCopyright Information Table of contents Safety Instructions Important safety instructionsSafety instructions for ceiling mounting of the projector Introduction Projector featuresIntroduction Shipping contents Projector exterior view Projector and remote control Controls and functionsLamp indicator light Color ModeVolume keys + AutoRemote control effective range Pull out the battery holderPositioning your projector Choosing a locationProjection dimensions Screen Center of lensConnecting a computer or monitor Connecting a computerConnection To connect the projector to a notebook or desktop computerTo connect the projector to a monitor Connecting a monitorMonitor Computer VGA to DVI Cable VGA cable Connecting Video source devices Connecting audioBest video quality Better video qualityConnecting a Component Video source device To connect the projector to a Component Video source deviceTo connect the projector to an S-Video source device Connecting an S-Video source deviceAV device Speakers Audio cable Video cable Cable To connect the projector to a composite Video source device Connecting a composite Video source deviceSpeakers AV device Video cable Audio cable Cable Starting up the projector OperationOperation See Timing chart on page 52 for details Using the menus Use / to highlight the System Setup Basic menuSystem Setup Basic System Setup AdvancedUtilizing the password function Setting a passwordIf you forget the password New passwordChanging the password Entering the password recall procedureDisabling the password function Switching input signal Adjusting the projection angle Adjusting the projected imageAuto-adjusting the image Fine-tuning the image size and clarity On the remote control. The KeystoneCorrecting keystone MODE/ENTER on the projector or EnterMagnifying and searching for details Selecting the aspect ratioAbout the aspect ratio Selecting a picture mode Picture modes for different types of signalsPC input signals D-Sub / Comp /2 analog RGB Video input signals S-Video, Video, D-Sub / Comp /2 YPbPrUsing Screen Color Fine-tuning the image quality in user modesSetting the User 1/User 2 mode Adjusting BrightnessAdjusting Color Adjusting TintAdjusting Sharpness Adjusting Brilliant ColorTo adjust the settings Color ManagementLocking control keys Hiding the imageOrder to draw the audiences full attention to To activate the High Altitude Mode Freezing the imageOperating in a high altitude environment Press MENU/EXIT on the projector or MenuPersonalizing the projector menu display Shutting down the projectorMenu system Menu operationMain menu Sub-menu Options Basic AdvancedDescription of each menu Color Mode SettingsReference ModeAuto Power Blank TimerTimer ProjectorSystem Setup Advanced menu Function Description Active VGA OutAudio MenuAdvanced Settings Reset All LampSecurity CurrentMaintenance Care of the projectorSetting Lamp mode as Economic Setting Auto Power OffLamp information Getting to know the lamp hourTiming of replacing the lamp Status MessageType number RLC-055 Replacing the lampLoosen the screw that secures the lamp Maintenance Tighten the screw that secures the lamp Resetting the lamp timerRestart the projector Indicators Power eventsLight Status & Description Lamp eventsTroubleshooting Cause RemedySpecifications Projector specificationsCeiling mount installation DimensionsTiming chart Signal Format Horizontal Frequency kHz Vertical Frequency Hz HorizontalCopyright information Copyright informationRS232 command table AppendixIR control table Pin assignment for this two endInterface RS-232 protocolBaud Rate Data Length Bit Parity Check None Stop BitContrast Write Blank on 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x09 0x01 VGA Hour Customer Support Limited Warranty How to get service PRJLW01 Rev hMexico Limited Warranty Viewsonic ProjectorNúmero Gratis DE Asistencia Técnica Para Todo México