Sanyo SCP-2700 instruction manual Connections, Connecting Antenna/Cable TV to

Page 11
Disconnect the antenna leads from the rear of the TV.

Connections

Tips

Depending on your TV and other equipment you wish to connect, there are various ways you could connect the DVD+VCR. Use connections described on pages 11-13. Please refer to the manuals of your TV, VCR, Stereo System or other devices as necessary to make the best connections.

For better sound reproduction, connect the DVD+VCR’s DVD/VCR AUDIO OUT jacks to the audio in jacks of your amplifier, receiver, stereo or audio/video equipment. See Optional, Preferred TV Connections on pages 12-13.

Caution

Make sure the DVD+VCR is connected directly to the TV. Tune the TV to the correct video input channel.

Do not connect the DVD+VCR’s DVD/VCR AUDIO OUT jacks to the phono in jack (record deck) of your audio system.

Do not connect your DVD+VCR via your VCR. The DVD image could be distorted by the copy protection system.

Connecting Antenna/Cable TV to

DVD+VCR

1

2 Identify the type of cable from your antenna. If it is a round cable as illustrated, it is a 75 ohm coaxial antenna cable. This cable will connect directly to the jack marked ANT.IN on your DVD+VCR.

Tip

If your antenna lead wire is a flat type antenna cable, connect it to a Antenna Adaptor (300-ohm to 75-ohm) (not supplied) and slip the Adaptor onto the ANT.IN jack. The Adaptor does not screw on to the DVD+VCR, it just slips over the jack.

Antenna Antenna

Cable TV

Wall Jack

Flat Wire

 

 

(300 ohm)

 

 

300/75 ohm

OR

OR

Adaptor

 

 

(Not supplied)

 

 

Rear of DVD+VCR

Without Cable Box

If your cable wire is connected to your TV without a converter or descrambler box, unscrew the wire from your TV and attach it to the ANT.IN jack on the DVD+VCR. Use the supplied round coaxial cable to connect between the DVD+VCR’s RF.OUT jack and the 75 ohm antenna input jack on the TV. With this connection, you can receive all midband, super band, and hyperband channels.

With Cable Box

If a converter is required in your cable system, follow the instruction below:

The cable hookup permits both TV and DVD+VCR operation.

To view or record CATV channel

1Tune the TV to the DVD+VCR output channel (CH 3 or 4).

2Set the DVD+VCR channel selector to the output channel of the Cable Converter box by pressing the CH/TRK (v/V) or number (0-9) of your DVD+VCR. (Example: CH3)

3Select the channel to view at the Cable Converter Box.

Notes

With this connection, you CANNOT record one program while viewing another.

If you are using a cable box to tune channels, it is not nec- essary to do Auto Channel Programming as indicated on page 15.

Cable TV

Wall Jack

Back Panel of

Typical Cable Box

Rear of DVD+VCR

PREPARATION

11

Page 10 Page 12
Image 11
Page 10 Page 12
Contents DVC-2700 Regulatory Information FCC Part Safety PrecautionsImportant Safety Instructions Table of Contents Playable Discs Remote control battery installationRemote Control Operation Range Before UseSetting the Output Source PrecautionsAbout Symbols Front Panel REC Display WindowRemote Control Rear Panel Connections Connecting Antenna/Cable TV toAudio/Video connection Connections Basic TV ConnectionsOptional, Preferred TV Connections RF coaxial connectionDigital Multi-channel sound Accessory Audio/Video A/V Connections toConnections Optional, Preferred TV Connections Menu Selection Setting the On-Screen DisplayBefore Operation VCR Part On-Screen Display OSD Channel Selection Before Operation VCR Part Setting the VCR Setup MenuPress v/ V to choose the Clock menu Before Operation VCR Part Setting the ClockAuto Clock Set Manual Clock SetOn-screen display operation Before Operation DVD PartGeneral Explanation On-Screen DisplayInitial Settings General Operation Before Operation DVD Part Initial SettingsVocal Dolby DigitalSample Freq. Frequency Dynamic Range Control DRCRating DVD Password DVD Setting your passwordChanging the 4-digit password If you forget your 4-digit passwordSpecial Effect Playbacks Operation with tape Normal PlaybackTo record one TV program while watching another Timer RecordingOperation with tape Normal Recording To pause the recordingProgram Priority Checking Erasing the Timer ProgramOperation with tape Dubbing and Editing Instant Timer RecordingChecking the Recording Time To extend the Recording TimeMTS Multi-Channel TV Sound Multichannel TV Sound Indicator MTSVHS Hi-Fi Stereo System MTS Broadcast Playback with Hi-Fi Stereo Audio SoundAdditional Information Operation with tape Tape Counter Memory FeatureMoving to another Chapter General FeaturesOperation with DVD Playing DVD Moving to another TitleOperation with DVD General Features Special DVD Features To stop playback at any other time, press Stop About MP3Operation with Audio CD and MP3 Discs Erasing the Complete Program List Programmed Playback CD MP3Programmed Playback with Audio CD and MP3 Discs Erasing a Track from Program ListSecurely TroubleshootingSymptom Cause Correction Moisture Condensation DVD+VCR is in Timer modeLanguage Code Language Code ListCountry Code Country Code ListGeneral SpecificationsVCR Specifications DVD Specifications
Related manuals
Manual 138 pages 8.38 Kb
Top Page Image Contents