Sanyo DTL-4800, RD2QD/NA Video Cassette Tapes, Correct tape thread check function

Page 18

VIDEO CASSETTE TAPES

Correct tape thread check function

If the correct tape thread check function is on, after the cassette tape is loaded, a mechanism will operate for about 12 seconds to check that the tape has been threaded (loaded) correctly and the cassette indicator “o” will blink during that period. If the tape is not loaded properly, the cassette will be ejected.

NOTES:

œThis function checks to make sure that the cassette has been correctly loaded. It is recommended to use this function to make sure the recordings are conducted reliably.

œIf during the tape thread check operation, the REC, PLAY, FF, REW or STOP button is pressed, the command will only be executed after the tape thread has been checked. Only the EJECT button will operate while the tape thread is being checked.

œIf in the (VARIOUS SET 2) menu “TAPE IN MODE” is set to “REC”, the recording indicator “ m” will light while the tape thread is checked. However, recording will only start after the tape thread check is completed. To cancel recording, press the STOP button.

1Press the MENU button to display the (MAIN MENU 1) menu.

2Press the SHIFT ] button to select the “4. VARIOUS SET 1” line, then press the MENU button.

øThe (VARIOUS SET 1) menu appears.

@@@@<VARIOUS@SET@1>

*THREAD@CHECK@@@@Y

*REMOTE@@@@@@@@@@EJECT

*EXT@TIME@ADJ.@@@01:00

*TAPE@END@OUT@@@@PRE

*EJECT@SET

@@EJECT@MODE@@@@@EJECT1

@@OPERATION@@@@@@SLAVE

3Press the DATA l (or j) button to set the desired mode.

Y. . . . . . . . . The correct tape thread check function is on

N. . . . . . . . . The correct tape thread check function is off

4Press the MENU EXIT button to save the setting.

Setting the Action to Take When a Cassette is Loaded

You can set the mode the VCR will go into when a cassette is loaded.

1Press the MENU button to display the (MAIN MENU 1) menu.

2Press the SHIFT ] button to select the “5. VARIOUS SET 2” line, then press the MENU button.

øThe (VARIOUS SET 2) menu appears.

@@@@<VARIOUS@SET@2>

*TAPE@IN@MODE@@@@STOP

*VIDEO@LOSS@@@@@@Y

*REC@SPEED@@@@@@@N

*CLOG@DETECT.@@@@Y

*SERIES@REC@IN@@@N

*MX@@@@@@@@@@@@@@SANYO

3Press the DATA l (or j) button to set the desired mode.

STOP . . . . . . Stays in stop mode

REC . . . . . . . Goes into recording mode

4Press the MENU EXIT button to save the setting.

English

17

Image 18

Contents Digital Precautions For the customers in CanadaDeclaration of Conformity Precautions Contents FeaturesAccessories STILL/PAUSE button Locations of Controls and IndicatorsFront Panel Search FRAME/FIELD button Eject button Menu Exit buttonOperation Mode Indicator Locations of Controls and IndicatorsOperation Indicators Digital DisplayOFF indicator Back Panel Male on the VCRO P Q R S T Installing the Ni-Cd Battery Protection against power failureConnections Power Cord Installation About the memory resetConnections ON-SCREEN Menus Main menusSub-menus ON-SCREEN Menus Clock Setting Setting the Language and ClockLanguage Setting Day of week is set automaticallySetting the Language and Clock Automatic Daylight Saving Time AdjustmentChanging the ON-SCREEN Display Selecting the On-screen DisplayChanging the Date/Time Display Position Video Cassette Tapes Correct tape thread check function Setting the Action to Take When a Cassette is LoadedVideo Cassette Tapes Various SET 1 menu appearsIf no tape management data is present on the tape Tape Management FunctionOperation If tape management data is present on the tapeSetting the Tape Management Function Tape Management FunctionTape Management menu appears Tape Management Conflict Display Conflict display sampleNormal Recording Recording speed mode is displayed on the digital displayPause/Still indicator N blinks Normal Recording Before startingField Recording Speed ModeNormal Recording HourConcerning the Number of Times Tapes can be Rerecorded on Recording CheckClog Detection Setting the Mode at the End of the Tape Action to Take when the Video Signal DeterioratesRecord SET menu appears Changes to the Recording Speed Mode During Recording Setup for use with a multiplexerRepeat indicator will light Autorepeat RecordingAutorepeat Recording Alarm Recording Alarm Recording SettingConnections to the Alarm IN/OUT Terminals Alarm RecordingAlarm Recording Counter Display Alarm Reset in terminalAlarm Search Alarm ScanPre Alarm Recording Setting Post Alarm Recording SettingRecording speed mode Recording duration Seconds Program Timer Recording Program Timer Recording Press the Data l or j button to select YTo Cancel a Program Timer Recording Setting the HolidaysChanging a Program Timer Recording To Cancel all Program Timer RecordingsThese portions will not be recorded Recording Using AN External Timer Input Connections Using a Multiplexer Trigger Shot Recording SetupTrigger Shot Recording Series Recording Series Recording SetupRecording will start in series recording mode Series recording connectionsContinous Loop Recording Setup Series RecordingLoop recording connection example with 2 VCRs Playback Search Forward and Reverse Tape CounterPlayback Field Advance Forward and ReverseDAY/TIME Search Day/Time SearchD Search 01 000000 will be displayed on screen Cancel the Security Lock Setting the Security LockSetting the Security Lock Setting and Canceling the Quick Method Security LockSetting the Buzzer If using the SET UP setting, continue with steps 4Buzzer SET menu appears Clock Adjustment Setting procedure on the first VCR is now completedEject terminal connection Setting the Cassette Eject ModeCassette Eject Setup Eject in terminalSW No Setup for RS-232C or RS-485 USEDIP Switches Setup ExampleRS-485 RJ-11 connector layout Setup for RS-232C or RS-485 USESetup for RS-232C or RS-485 Use RS-485 ConnectionRS-232C 9-pin connector layout Pin Signal Operation Signal directionPOWER/DEW/USED Time menu appears Tape END OUT Terminal Timer OUT TerminalOutput Terminals COM TerminalRemote Jack Remote control settingOutput Terminals NON REC OUT terminalMaintenance Maintenance Maintenance TableMaintaining and Checking The Mechanism Troubleshooting Guide After a Power FailureSystem Down Specifications Sanyo Industrial VCR Warranty Weekdays 830 AM 500 PM Pacific TimeRD2QD/NA

Related manuals

Manual 57 pages 44.49 Kb