Sanyo DTL-4800 Output Terminals, Tape END OUT Terminal, Timer OUT Terminal, COM Terminal

Page 50

OUTPUT TERMINALS

TAPE END OUT Terminal

œDuring recording, when the end of the tape is reached or when approximately 5% of the tape remains, the output becomes 0V (Low).

œTo reset the output, press the STOP or EJECT button.

œDuring autorepeat recording, when the end of the tape is reached, the output becomes 0V (Low) for about 2 seconds only.

End of the tape or approximately 5% of the tape remaining Output reset

5V (H)

(Output impedance: 5.7 kΩ) 0V (L)

TAPE END OUT Terminal Output Setting

1Press the MENU button to display the (MAIN MENU 1) menu.

2Press the SHIFT ] button to select the “4. VARIOUS SET 1” line, then press the MENU button.

øThe (VARIOUS SET 1) menu appears.

@@@@<VARIOUS@SET@1>

*THREAD@CHECK@@@@Y

*REMOTE@@@@@@@@@@EJECT

*EXT@TIME@ADJ.@@@01:00

*TAPE@END@OUT@@@@PRE

*EJECT@SET

@@EJECT@MODE@@@@@EJECT1

@@OPERATION@@@@@@SLAVE

3Press the SHIFT ] (or \) button, until the “TAPE END OUT” setting is flashing.

4Press the DATA l (or j) button to select the desired output mode.

PRE . . . . . . . The output becomes 0 V (Low) when approximately 5% of the tape remains (if recording has been started at the beginning of the tape) and/or when the end of the tape is reached (if recording has not been started at the beginning of the tape).

END . . . . . . . The output becomes 0 V (Low) when the tape reaches the end.

5Press the MENU EXIT button to save the setting.

WARNING OUT Terminal

œIf the tape stops or other problem (the heads are dirty, there is a problem with the battery or the cooling fan, etc.) the output becomes 0V (Low).

œTo reset the output, press the STOP or ALL RESET button or unplug the power cord then plug it back in.

Tape movement stop

Output reset

5V (H)

(Output impedance: 5.7 kΩ) 0V (L)

NOTE:

œIf the output is 0V (Low) due to the clog detect function, it can be reset by simply pressing the STOP button.

TIMER OUT Terminal

œDuring timer recording DC 12 V (High) are output. (During timer recording stand-by mode, the output is 0V (Low).)

Timer recording

12V (H)

(Output impedance: 5.7 kΩ) 0V (L)

COM Terminal

œCommon GND (ground) terminal when connecting other terminals to external devices.

SW OUT Terminal

When recording, a pulse signal is output at the SW OUT terminal.

This terminal is usually connected to the switch input (SW IN) of devices like a camera switcher unit, or a quad compressor.

FIELD: 16.7 msec.

5V (H)

(Output impedance: 5.7 kΩ) 0V (L)

English

49

Page 49 Page 51
Image 50
Page 49 Page 51
Contents Digital Declaration of Conformity PrecautionsFor the customers in Canada Precautions Accessories ContentsFeatures STILL/PAUSE button Locations of Controls and IndicatorsFront Panel Search FRAME/FIELD button Eject button Menu Exit buttonOperation Mode Indicator Locations of Controls and IndicatorsOperation Indicators Digital DisplayOFF indicator Back Panel Male on the VCRO P Q R S T Connections Installing the Ni-Cd BatteryProtection against power failure Connections Power Cord InstallationAbout the memory reset Sub-menus ON-SCREEN MenusMain menus ON-SCREEN Menus Clock Setting Setting the Language and ClockLanguage Setting Day of week is set automaticallySetting the Language and Clock Automatic Daylight Saving Time AdjustmentChanging the Date/Time Display Position Changing the ON-SCREEN DisplaySelecting the On-screen Display Video Cassette Tapes Correct tape thread check function Setting the Action to Take When a Cassette is LoadedVideo Cassette Tapes Various SET 1 menu appearsIf no tape management data is present on the tape Tape Management FunctionOperation If tape management data is present on the tapeTape Management menu appears Setting the Tape Management FunctionTape Management Function Tape Management Conflict Display Conflict display sampleNormal Recording Recording speed mode is displayed on the digital displayPause/Still indicator N blinks Normal Recording Before startingField Recording Speed ModeNormal Recording HourClog Detection Concerning the Number of Times Tapes can be Rerecorded onRecording Check Record SET menu appears Setting the Mode at the End of the TapeAction to Take when the Video Signal Deteriorates Changes to the Recording Speed Mode During Recording Setup for use with a multiplexerAutorepeat Recording Repeat indicator will lightAutorepeat Recording Alarm Recording Alarm Recording SettingConnections to the Alarm IN/OUT Terminals Alarm RecordingAlarm Recording Counter Display Alarm Reset in terminalAlarm Search Alarm ScanRecording speed mode Recording duration Seconds Pre Alarm Recording SettingPost Alarm Recording Setting Program Timer Recording Program Timer Recording Press the Data l or j button to select YTo Cancel a Program Timer Recording Setting the HolidaysChanging a Program Timer Recording To Cancel all Program Timer RecordingsThese portions will not be recorded Recording Using AN External Timer Input Trigger Shot Recording Connections Using a MultiplexerTrigger Shot Recording Setup Series Recording Series Recording SetupRecording will start in series recording mode Series recording connectionsLoop recording connection example with 2 VCRs Continous Loop Recording SetupSeries Recording Playback Search Forward and Reverse Tape CounterPlayback Field Advance Forward and ReverseD Search 01 000000 will be displayed on screen DAY/TIME SearchDay/Time Search Cancel the Security Lock Setting the Security LockSetting the Security Lock Setting and Canceling the Quick Method Security LockBuzzer SET menu appears Setting the BuzzerIf using the SET UP setting, continue with steps 4 Clock Adjustment Setting procedure on the first VCR is now completedEject terminal connection Setting the Cassette Eject ModeCassette Eject Setup Eject in terminalSW No Setup for RS-232C or RS-485 USEDIP Switches Setup ExampleRS-485 RJ-11 connector layout Setup for RS-232C or RS-485 USESetup for RS-232C or RS-485 Use RS-485 ConnectionPOWER/DEW/USED Time menu appears RS-232C 9-pin connector layoutPin Signal Operation Signal direction Tape END OUT Terminal Timer OUT TerminalOutput Terminals COM TerminalRemote Jack Remote control settingOutput Terminals NON REC OUT terminalMaintenance Maintaining and Checking The Mechanism MaintenanceMaintenance Table System Down Troubleshooting GuideAfter a Power Failure Specifications Sanyo Industrial VCR Warranty Weekdays 830 AM 500 PM Pacific TimeRD2QD/NA
Related manuals
Manual 57 pages 44.49 Kb
Top Page Image Contents