Speco Technologies CS16 manual Network Setup

Page 43

16-Channel Digital Video Recorder

Network Setup

Figure 44 — Network menu.

Network

Highlight Network in the Network menu and press the button.

Highlight the first box beside Remote Watch bps/ips. Press the Up and Down arrow buttons to set the Transfer Speed from 50Kbps to 100Mbps.

Highlight the second box beside Remote Watch bps/ips. You can select the unit of measure for the transfer speed between: bps and ips. Press the button to set the transfer speed.

Highlight the box beside Remote Watch Quality and press the button. You can select the Quality from: Very High, High, Standard and Basic. Press the button to set the Quality.

Figure 45 — Network setup screen.

Highlight the box beside Remote Watch Resolution and press the button. You can select the Resolution from: Very High (D1), High (Half D1) and Standard (CIF). Press the button to set the Resolution.

NOTE: The higher Quality and Resolution settings require higher Transfer Speed settings. The transfer speed you set is the maximum speed. Depending on the network environment, this speed may not be achieved.

You can limit the network bandwidth settings so that system does not consume too much network bandwidth. Highlight the box beside Network Bandwidth Limit and press the Up and Down arrow buttons to set the desired maximum bandwidth from 10Kbps to 100Mbps.

NOTE: When limiting the network bandwidth, the remote watch image on the PC running Speco Central or Speco Remote might not be displayed properly.

The DVR supports two-way audio communication between a local system and a PC running Speco Central. Highlighting the box beside Remote Audio Channel and pressing the button allows you to select the audio channel that sends audio to the remote site. Selecting Select From Speco Central will send audio of the channel selected from Speco Central.

NOTE: Depending on network conditions, audio might be interrupted or out of synchronization during transmission.

Highlight Enable SSL for Transferring Data and press the button to toggle between On and Off. When it is On, the security of data except video and audio transmitted for remote monitoring or remote recording can be enhanced by using the SSL (Secure Sockets Layer) authentication. When using the SSL function, the DVR cannot be connected with a remote program or a network keyboard which does not support the SSL function.

CAUTION: The remote connection will be disconnected temporarily after changing the SSL settings.

NOTE: While the SSL function is enabled, the network transfer speed you selected may not be achieved.

This product includes software developed by the OpenSSL Project for use in the OpenSSL Toolkit (http://www.openssl.org/).

35

Image 43
Contents Page Page Compliance Notice of FCC Weee Waste Electrical & Electronic Equipment Table of Contents Digital Deterrent List of Illustrations Motion Detection Settings screen Technical Overview FeatureTypical DVR installation Required Installation Tools Package ContentsRS232 Port Power Cord ConnectorVideo Out Audio In/OutNetwork Port Alarm Input/OutputFactory Reset Switch RS485 PortOperation Instruction Esc Button Front Panel ControlsMenu Button Copy ButtonArrow Buttons Power LEDPlay/Stop Button Camera ButtonsSequence Button Remote Control ButtonsLogin/Logout Button ID ButtonZoom Button Alarm ButtonPlayback Buttons Layout ButtonInitial Unit Setup Turning on the PowerPTZ Control Buttons System Setup Setup ScreenInformation Information setup screen Date/Time Date/Time setup screenStorage Holiday setup screenStorage device UserUser setup screen EZ Setup screen EZ SetupDate/Time Setup Internet Connection Shutdown Recording SetupRecord Record Settings screen Schedule Schedule setup screenPre-Event Schedule Settings Advanced Mode setup screenAlarm-In Event SetupMotion Detection Alarm-In Actions 1 screenMotion Detection Settings screen Motion Detection Actions 1 screen Video LossVideo Blind Video Loss Settings screenDVR checks to see if anything is blinding a camera Text-In Text-In Settings screenText-In Actions screen System EventHighlight the Storage tab, and the Storage screen displays Event Status Check Alarm-In and Check Recording will beNetwork Network SetupHighlight the LAN tab, and the LAN screen displays Dvrns setup screen Notification Rtsp setup screenHighlight the + and press the button to add a mail recipient Notification SNS setup screen Camera Devices SetupHighlight the PTZ tab, and the PTZ setup screen displays Audio Alarm-OutDigital Deterrent Display OSD screen DisplayMain Monitor screen Remote Control setup screen Remote ControlOperation Instruction Live Monitoring Menu Live MonitoringFreeze Alarm Zoom Mode Active Cameo ModePTZ Mode Event Monitoring Covert Camera Recording VideoRecording Audio Playing Recorded VideoSelect Playback Camera menu Searching VideoSearch Search MenuBookmark Data Source Event Log SearchRecord Table Search screen Record Table SearchCalendar Search Configuration Digital Deterrent section for more detailsMotion Search screen Motion SearchText-In Search screen Text-In SearchClip-Copy BookmarksOperation Instruction Preparing the USB hard disk drive in Windows USB Hard Disk Drive PreparationSearch Example Text-In Search ExamplesSpeco Remote Web Monitoring Mode Web Search Mode Operation Instruction Time Overlap Map of Screens System Log Notices TroubleshootingSpecifications Error Code NoticesStorage