Marantz PV6111W manual How to Identify a Cable Converter

Page 68

Operation of the Remote Control for Other Devices (Continued)

How to Identify a Cable Converter

POWER DTV VCR/ DVD/

STB TV CATV

PERSONAL PREFERENCE

A B C D

ENTER

VOL

CH

MENU

 

AV MODE

 

MUTE

 

 

INPUT

 

ANT-A/B

 

DISPLAY

 

ENT. FLASHBACK

TWIN

Q-SOUND

PICTURE

CH

VIEW

MODE

 

INPUT

TITLE

REW

FF

CH/SKIP PAUSE STOP REC

VCR/DVD

DDFCPOWER

To Identify Your Cable Converter –Direct Entry Method

Use the following steps and list (on page 69) to quickly find the remote control code for your cable TV converter.

• First look up your converter’s remote code number on page 69 before continuing the direct code entry steps below.

DVD/

CATV

(1) Press

and the button lights.

 

 

 

 

 

DISPLAY

 

 

 

(2) While holding down

, press

on your remote control.

 

DVD/

 

 

 

 

Make sure

CATV

 

 

 

 

lamp goes out and then release both buttons.

 

 

 

DISPLAY

 

 

(3) Within ten seconds after releasing

and

, enter your converter’s

two-digit code number using DIRECT ACCESS (

~

) (refer to the list

on page 69). The code should be identified within two minutes.

DVD/

CATV

lights for two seconds and then goes out. This indicates that the setting

is performed successfully.

• The remote control is now ready to send commands to your converter.

Depending on the model, year produced, brand, and type of CATV converter, some

Note

models may not be compatible with the remote control.

Identifying your Cable Converter through the Search method

(1) While pointing the front part of the remote control towards the infrared sensor

of the cable converter, press

DISPLAY

and hold them down for up

and then

to two minutes. Be careful not to let the cable converter scan more than five channels when the indicator starts to increase. If you continue to hold down the buttons after five channel scans, the proper remote code can be passed up and the two-minute cycle will have to be repeated.

• The remote control then searches in order for the cable converter Brand

Code Number (listed on page 69).

DISPLAY

(2) At the instant when the cable converter channel changes, release

 

and

and the procedure will be completed. If a channel change does not

occur on the cable converter within two minutes, read the identifying instructions again and repeat the steps. Should a channel change still not occur, the remote will most likely not operate your cable converter.

68

Image 68
Contents Model PV6111W User Guide Contents Important Information Picture Burn Prevention Public Viewing of Copyrighted MaterialS2898A Main Features Supplied Accessories Before Operating Your Rear Projection TVBefore Operating Your Rear Projection TV Universal Remote Control Type of connectorAntenna Connections AntennasConnection with Converter/Descrambler Box without VCR Connection with Antenna Cable and VCR Connection with Antenna Cable Main Unit To open the coverBasic Remote Control Functions Infrared Transmitter Window PowerName of button Operation EZ Setup on First Power On Menu screen Press Menu to access MainMenu Functions Menu Summary TIMER/CLOCK You can adjust the screen size. See pages 31 ~Clock SET TIMER/CLOCK Sleep Time TV-ON Time Press To exitHow to set Closed Caption Closed CaptionCursor to CC Closed Caption Cursor to an item you want to setVideo Adjust Press Enter or To accessVideo mode Menu screen and then usePRO Adjust Mark to PRO ADJ. modeAccess the PRO ADJ. mode Then press Enter orTo set other PRO adjustments Video NROPC optical control Press or to select On or OFF, and then pressAudio Adjust Other Audio Settings AdjustMark to an item e.g Equisound you want toMTS/SAP Select mode To access the MTSCursor to MTS and then press ModeScreen Adjust Screen adjustment items vary depending on Screen size modePress or to adjust Vertical position, then press Cursor to ScreenParent Control V-CHIP operation Mpaa Rating ExampleExample 1.1 Age-Based setting Example 1.2 Age-Based settingExample 2.1 Content-Based setting Example 2.2 Content-Based settingCursor to Parent Ctrl How to Set V-CHIPParent Control First Setting Mpaa Rating Rating on TV RatingRepeat steps 1 to 4 of Mpaa Additional mode Repeat steps 3 to 5 for other settings you want to adjust OTHERS, then pressUse To move Cursor to an item e.g Canadian English you wantTurn on V-CHIP Block Repeat steps 1 to 4 of MpaaRating on Mark to StatusDisplayed Chip Block temporarily will be canceledPress Enter Input Secret No. will be Enter the 4-digit Secret No. by using Direct Access ~ V-CHIP select mode will be displayedRepeat the configuration of the V-CHIP Block on Repeat steps 1 to 2 of Mpaa Rating onParent Control View Timer View TimerPress To move Mark to Status To set StatusTo on to turn on the View If you want to set OFF TIME, select OFF Time in stepChannel Setup AIR/CABLE SettingCursor to CH Setup CH Setup modeCable Setting on CH Search modeSaving Broadcast TV channels to memory Channel Search Repeat steps 1 to 3 of AIRSetting on CH Memory modeRepeat steps 1 to 3 of AIR/CABLE Mark to CH MemoryFavorites mode FavoritesTo move Mark to the desired Position To input the channel number Into the memoryCable Setting on UNIV. Plus modeUniversal Plus Function Repeat steps 1 to 3 of AIRSetup Cursor to SetupSET UP mode Language modeGray Screen Cursor to onEnergy Save Convergence Adjust Energy Save setting onAccess the CONVER. ADJ. mode Repeat steps 1 and 2Then Use Move the blue cross to match it to Input Mode Access the Input ModePress Enter or Press To select Instrument HD/DVDCH/INPUT ID Press Mode Changing Screen SizeSelecting Ddfc Mode or AV Mode Selecting Ddfc ModeSelecting AV Mode 540PMulti-screen Function View two Screens Twin Picture ScreenPress Picture to make the left part Screen become larger To return to the initialFunction. By changing a full screen into Making Notes From the Program Content Freeze ScreenPress Freeze Freeze function serves as a memo Searching for a Program on a Different Channel Search Screen Press Search to display 3-SEARCH ScreenRight screens Twin picture displayPress Swap to interchange the left Using your Remote control with a DTV STB Decoder Using Your Remote With Your Rear Projection TVTo Identify Your VCR Direct Entry Method How to Identify a VCRTips on Identifying your VCR through the Search method VCR Brand Remote Control Code Number How to Identify a DVD Player While holding Press On your remote controlTo Identify Your DVD player -Direct Entry Method Press and the button lightsHow to Identify a DTV STB Digital TV Set-Top Box Identifying your DTV STB through the Search methodTo Identify Your DTV STB -Direct Entry Method Make sure STB lamp goes out and then release both buttonsTo Identify Your Cable Converter -Direct Entry Method How to Identify a Cable ConverterIdentifying your Cable Converter through the Search method Specifications Using the Video and Audio Input Jacks Connecting video equipment for video playbackVideo playback Using the Audio Output Jacks Before Calling for Service Quick Service Check List ProblemUnidad Principal Sección de control delanteraFunciones Básicas del Control Remoto Botones de selecció n del modo del control remotoProblema Antes de llamar al Servicio de ReparacionesCommandes avant Unité PrincipaleFonctions de Base de la Télécommande Capteur INFRA-ROUGEAvant de faire appel au Service Après-vente Liste DE Vérification Rapide ProblèmeDimensions for Installation Page Page Page Limited Warranty for the Marantz Rear Projection Television