Setting Up VCR Channels with or without remote

The VCR 1 CHAN function lets you

-Setting Up VCR Channels (with or without remote)

program to which channel the TV will automatically tune when you press the VCR1 button on the remote. This is handy if you connect a VCR to your TV. You will no longer have to remember to which input jacks the VCR is connected because the TV will remember for you.

For example, if you connect a VCR's

AUDIO/VIDEO OUT jacks to the TV's INPUT 1 jacks (as shown on page 35), you will no longer have to remember to select channel 91 on the TV to see what the VCR is playing. By entering channel 91 next to the VCR 1 CHAN function, the TV will automatically tune to channel 91 each time you press the VCR1 button on the remote.

This function is especially convenient if you have a compatible VCR that can be operated by the VCR1 button on the remote. Pressing VCR1 will then not only turn on the VCR but also automatically tune the TV to the proper channel for viewing the picture from the VCR. You can program most brands of remote- controllable VCRs to respond to the VCR1 button as described on

igage 38.

The VCR 2 CHAN function works

the same way. It lets .you program to which channel the TV will

1.Repeatedly press MENU.PROG to select SETUP MENU, and then press + or - to display the setup functions,

Repeatedly press MENU.PROG to select the VCR 1 CHAN function.

2.Enter the channel number you want to program by pressing two digit buttons on the remote control. (The channel number you enter is the channel to which the TV will tune automatically when you later press the VCR1 button on the remote.)

3.Press the + button to program the channel number you selected into the TV's memory.

4.If you have another VCR connected to the TV, press MENUopROG to select the VCR 2 CHAN function.

. Enter the channel number you want to program by pressing two digit buttons on the remote control. (This is the channel number to which the

TV will tune automatically when you later press the VCR2oLD button on the remote.) See the notes below if

you are unsure about which channel number to enter.

6.Press the + button to program the channel number you selected into the VCR 2 CHAN function memory.

automatically tune when you press the VCR2oLD button on the remote.

Note: Pressing the - button here will

turn off this feature and display

You can program most brands of

remote-controllable VCRs to respond to the VCR2°LD button as described

Note: Pressing the - button here wiU turn

off this feature and display

VCR 1 CHAN: OFF again.

VCR 2 CHAN: OFF again.

on page 38. Pressing the VCR2oLD button will then not only turn on the VCR but also automatically tune the TV to the proper channel for viewing the picture from the VCR.

Note: Pressing the VCR1 or VCR2oLD button does not change between ANTA and ANT B antenna inputs. Press the ANTENNA button on the remote control to change antenna inputs if necessary.

Notes about Entering Channel Number:

•Enter channel 91 if VCR is connected to the TV's audio and Video INPUT 1 jacks.

•Enter channel 92 if VCR is connected to the TV's audio and video INPUT 2 jacks.

•Enter channel 90 if you have a Super-VHS VCR that is connected to the TV's S-VIDEOconnector and INPUT 1 audio jacks (labeled L and R/MONO).

•Enter channel 03 (or 04) if you did not use any audio/video cables and connected the VCR to the TV's round antenna jack labeled ANTA or ANT B. Enter the same channel number (03 or 04) as the position of the VCR's CH3/CH4 switch. This is the channel to which you must tune your TV for viewing signals from your.VCR.

•Refer to pages 35-36 if you want to review details about connecting your VCR to your TV.