RCA P52731, P46732, P46738, P52730, P46731 Programming Remote To Control with remote only, Cable Box

Page 35

The universal remote is preprogrammed to control an satellite receiver. If your cable box has its own remote to change channels, you will probably be able to program the TV's remote to control both the TV and the cable box.

The TV's remote is designed to control several brands of cable boxes. To program the remote, press and hold the

SAT.CABLEbutton, then the two-digit

code number for your brand of cable box. Refer to the chart below to find

the code number for your cable box. Press the POWER button next to confu-rn operation.

You may need to try each of the code

numbers listed for your brand until you find the one that works.

After the TV's remote is programmed, you'll be able to turn on the cable box by pressing SAT.CABLE, then POWER. You can change channels on the cable

box by pressing the CHAN buttons whenever the remote is in the "cable"

mode. To put the remote in the "cable" mode, press the SAT.CABLE button. Press the TV button to put the remote backinto the TV mode so the remote buttons will control the TV again.

Programming Remote To Control _(with remote only)

1.Refer to the chart below to find the code number that corresponds to the brand name of your cable box. Keep this number in mind. If more than one number is listed, you may need to try each one separately until you find the one that works.

2.Press and hold the SAT.CABLE button on remote.

3.Press two number buttons (first one, then the other) to enter the code number for your brand of cable box. Note: You must press the two

number buttons while pressing the DSSoCABLEbutton.

Cable Box

4.Point the remote at the cable box and press the POWER button to test the code number.

If the right number was entered, the cable box should turn on. Pressing the CHAN buttons should then

also change channels on the cable box.

If the cable box does not react to the remote (or if the remote turns on the cable box but does not

change channels), repeat steps 1 thru 4 with another code number.

Operating Notes:

After the remote is programmed, it

will turn on the cable box whenever you press SAToCABLE and then POWER. To turn off the cable box, press SAToCABLE, then POWER.

To change channels on the cable box, press SAToCABLE then CHAN up or down.

You may have to reprogram the remote control if you change its batteries. Try not to press any buttons while changing batteries.

Depending on the age, brand, model, and type of equipment, some models may not be able to respond to the remote.

ABC

 

..............................................................

:.22,46,53,54

Randtek.

......................................................................................

07,08

Anvision

 

 

07,08

RCA

 

00,27

Cablestar

 

 

.07,08

Regal

 

03,12,13

Diamond

 

 

 

56

Regency

......................................................................................

02,33

Eagle

 

 

 

 

07,08

Samsang

..... _

 

44

Eastern

International

.......................................................................

 

02

Scientific

Atlanta

03,22,35,63,64

General

Instrument

...... ............................................

,

46

Signature

..........................................................................................

 

46

GI 400

_

04,05,15,23,24,25,30,36

Sprucer

..................................

27

Hamlin

 

 

 

03,12,13,34,48

Starcom

 

 

46

Hitachi

 

 

 

37,43,46

Stargate

2000

 

58

Jerrold

 

04,05,15,23,24,25,30,36,45,46,47,62,65

 

Sylvania

......................................................................................

11,59

Macom

 

 

 

37,43

Teknika

 

 

06

Magnavox

 

07,08,19,21,26,28,29,32,33,40,41

 

Texscan

 

10,11,59

NSC

 

 

 

 

 

09

Tocom

 

17,21,49_0,55

Oak

 

 

 

 

01,16,38

Unika

. ............. 31,32,41

Oak Sigma

;

 

16

Universal

............................................................................

:..51,52,60

Panasonic

........................

_

03,27,39,61

Viewstar

........................................

07,08,19,21,26,28,29,32,33,40,41

 

Philips

 

 

07,08,19,21,26,28,29,32,33_40,41

 

Warner Amex

 

44

Pioneer

 

 

 

18,20,44

Zenith

14,42,57,61

Note:

Refer to

the

information

sheet packed with

your remote

control

for the latest list of brand names

and code numbers.

Because

this list

is constantly growing, the information sheet packed with your remote control may be a later version of this list and contain additional

 

brands

and/or

code

numbers.

 

 

 

 

 

 

 

33

Image 35
Contents Users Guide Record Vital Information Here Mail Your Registration Card TodayTable of Contents Position TV in room Install batteries in remote control Details are onUnpack TV and accessories May cause overheating, damage, or the risk of fire hazardTurn on TV, adjust the volume, and select a channel Set the clock Review menus Review other features+ Buttons VOL Volume ButtonsMenu Button Commercial Skip Channel Label Parental Contro ChannelChannel Label Captioning Commercial SkipTurn the remote control face down Installing/Replacing BatteriesDiscover exactly which buttons will control it Then press Power button to turn on thatBasic Operation Theory StepVOL Buttons TV ButtonChan Buttons Picture-in-Picture Buttons Number ButtonsArrow Buttons Starting Picture-in-Picture PIP 20 30 0 sO 60 70 80 ,0 Custom Picture Memory for Input Channels Adjusting for a.Color Picture that Pleases YouOr down Pressing VOL up or Converging Aligning the Colors --with remote onlyUntil the Convergence function is selected Pressing+ or- to Adjust itTurning OnSRS Page Turning Captioning Off Setting Closed Captioning with or without remoteRemaining Setting Sleep Timer with or without remoteTime will stay set but the Alarm ON/OFF Setting the AlarmErasing Labels When finished, the display willActivatingParental Control with remote only An active channel may be missed Adding Video Input Channels to Channel MemoryChanging Antenna Input with remote Connecting a cable-TVsystem orSetting Up VCR Channels with or without remote SettingUp Cable Box Channel with or without remote Positioning Speakers to Avoid Interference Plugging in Power CordsTurning Off Power Before Connecting Components Positioning Cables to Avoid HumScween Cab Scrambled Cable-TV Channels Back Ofvcr Cable Box Programming Remote To Control with remote onlyScrambled Cable-TV Channels Simplified Method Preferred MethodTG!roARreaeSeptithn OperationSelect OUT jacks. To record from an,S-Video component Connector do not come thruSpecial Recording onto VCR Number Buttons Chan Channel ButtonsDepending on which button you Power switch on their remote controlsProgramming Remote To Control Other Brands of VCRs VHSor Standard VHS Camcorder VHS or Standard VHS CamcorderComputers and Other Equipment with Audio/Video Outputs @,@Connection Amplifier or Cassette Tape Deck Audio AmplifierAudio Cassette Recorder or Amplifier Audio Equipment Programming Remote to ControlHelpful Hints Connecting Speakers to Back of TVSpeakers to Back of Amplifier or ReceiverAntenna Cables Compatible ComponentsGeneral Cable Information Audio/Video CablesForm Tocom Simple Touch,,, Remote ControlAccessoIv This offer is valid only in the 50 United States and Canada To order accessories, contact your local dealerInternational Orders United States and Canada OrdersPage Turns off while playing PowerCantselectcertainchannel Noisystereoreception Noclosedcaptioning Turnonthe Captioning function What we will do How you get serviceCommercial ButtonsCRF Ting a Greener Future