Pioneer PDP 503CMX, PDP 433CMX Connection Panel, Operating range of the remote control unit

Page 14

Part Names and Functions

English

Operating range of the remote control unit

When operating the remote control unit, point it at the remote sensor (Î) located on the front panel of the main unit. The remote control unit is operable up to 23 feet (7 m) from the unit and within a 30 angle on each side of the sensor.

Connection Panel

The connection panel is provided with two video input jacks and one video output jack. Audio input and speaker output jacks are also provided, together with a CONTROL IN/OUT connector for connecting to PIONEER components bearing the Î mark.

For instructions regarding connections, consult the pages noted in parentheses by each item.

1SPEAKER (R) terminal

Part Names and Functions

7 m (23 feet)

30˚

30˚

Remote Sensor

If you are having difficulty with operation of the remote control unit

The remote control unit may not operate if there are objects placed between it and the display.

Operational distance will gradually become shorter as the batteries begin to wear out; replace weak batteries with new ones as soon as possible.

This unit discharges infrared rays from the screen. Placing a video deck or other component that is operated by an infrared remote control unit near this unit may hamper that component’s reception of the remote control’s signal, or prevent it from receiving the signal entirely. Should this occur, move the component to a position further away from this unit.

Depending on the installation surroundings, this unit’s remote control unit may be influenced by the infrared rays discharged from the plasma display, hampering reception of its rays or limiting its operational distance. The strength of infrared rays discharged from the screen will differ according to the picture displayed.

For connection of an external right speaker. Connect a speaker that has an impedance of 8 -16 Ω (page 14).

2CONTROL IN/OUT (monaural mini jacks)

For connection of PIONEER components that bear the Î mark. Making CONTROL connection enables control of this unit as a component in a system (page 15).

3COMBINATION IN/OUT

DO NOT MAKE ANY CONNECTIONS TO THESE TERMINALS.

These terminals are used in the factory setup.

4RS-232C

DO NOT MAKE ANY CONNECTIONS TO THIS TERMINAL.

This terminal is used in the factory setup.

5INPUT1 (mini D-sub 15 pin)

For connection of a personal computer (PC) or similar component. Make sure that the connection made corresponds to the format of the signal output from the connected component (pages 12 to 14).

6OUTPUT (INPUT1) (mini D-sub 15 pin)

Use the OUTPUT (INPUT1) terminal to output the video signal to an external monitor or other component.

Note: The video signal will not be output from the OUTPUT (INPUT1) terminal when the main power of this unit is off or in standby mode.

(page 13)

7INPUT2 (BNC jacks)

For connection of a personal computer (PC) or similar component. Make sure that the connection made corresponds to the format of the signal output from the connected component (pages 12 to 14).

8

En

Page 13 Page 15
Image 14
Page 13 Page 15
Contents PDP-503CMXPDP-433CMX English Operating Instructions Safety Precautions Safety PrecautionsImportant Safety Instructions Iii Contents Features Screen Displays How to Use This ManualBefore Proceeding Example of PDP-503CMX Screen DisplayAbout operations in this manual Press 5/∞/2/3 to adjust the valuePress 5/∞ to select the item to be adjusted Before Proceeding Press Menu to display the menu screenChecking Supplied Accessories Main unit Part Names and FunctionsMain Unit Operation panel on the main unitWhen handling the remote control unit Remote Control UnitInserting the batteries Remote control unit Operating range of the remote control unit Connection PanelAudio Input Stereo mini jack Illustration depicts PDP-503CMX model~ Speaker L terminal Audio Output Stereo mini jackInstallation using the supplied display stand Installation and ConnectionsInstallation of the Unit Installation and ConnectionsRear view diagram PDP-433CMX Wall-mount installation of the unitRear view diagram PDP-503CMX Side view diagramConnection to a personal computer When connecting to INPUT2Connection to INPUT1 and INPUT2 Connection of separate Sync analog RGB SourceConnection of G on Sync analog RGB source When connecting to INPUT1When connecting to INPUT2 When connecting to Output INPUT1 Connection of composite Sync analog RGB Source Connecting the speakersAudio Connections Making connections to the audio inputs on this unitPower Cord Connection Control Cord ConnectionTo remove speed clamps How to Route CablesTo attach the speed clamps to the main unit Screen Mode setup Setting Up the SystemSetup after Connection Press 2/3 to select SET UPSetting Up the System Clamp Position setupSetup of Clamp Position Press SET to select LockedSelecting an Input Source Press STANDBY/ON to put this unit in the operation modeOperations Before you begin, make sure you havePress Muting on the remote control unit To adjust the volumePress Volume on the remote control unit Press Display on the remote control unitChanging the screen size During personal computer signal inputScreen Size Selection Press Screen Size to select the sizeMoving the screen position upward or downward Supported only on PDP-503CMXPartial Image Enlargement Management or Auto Power OFF mode Automatic Power OFFPress 5/∞ to select either the Power When using InputTo reset Picture mode settings to the default Display Panel AdjustmentsAdjusting the Picture Quality Adjusting the Image Position and Clock Automatic Adjustment Display Panel AdjustmentsTo reset Screen mode settings to the default Other Operations Other OperationsRewriting the Input Display Press SET to select Input LabelPress 2/3 to select Option Power Control FunctionPress SET to select Power Control Press MenuPress 5/∞ to select Audio OUT Audio Output Audio OUTOther Operations Press SET to select Input About the self diagnosis mode CleaningTroubleshooting Additional InformationGeneral problems Problems commonly mistaken as breakdownAdditional cautions STANDBY/ON indicatorPanel sticking and after-image lag General PDP-433CMX AccessoriesGeneral PDP-503CMX Input/outputInformation PC signal compatibilty table INPUT1, INPUT2Supplement 1 -1/2 PDP-503CMX AdditionalSupplement 1 -2/2 PDP-433CMX Supplement Explanation of Terms Pin No Input Output
Top Page Image Contents