Pioneer PDP 433CMX, PDP 503CMX specifications Control Cord Connection, Power Cord Connection

Page 21

Installation and Connections

Control Cord Connection

When control cord connections are made, remote control operation of connected PIONEER components that bear the Î logo mark is done through the remote sensor on this unit.

When the connection is made to the CONTROL IN jack on another unit, the remote sensor of that component will no longer receive signals. Point the remote control unit of the connected component at the remote control sensor on this unit to control.

Notes

÷Make sure the power is turned off when making connections.

÷Please complete all component connections before making control cord connections.

CONTROL

IN

Main unit

OUT

CONTROL

IN OUT

CONTROL

IN

OUT

CONTROL

IN

OUT

The control cables (not supplied) are monaural cables with mini plugs (no resistance).

Power Cord Connection

Connect the power cord after all component connections have been completed.

1

2

1Connect the power cord to this unit.

2Plug the power cord into a power outlet.

CAUTION

÷Use only the power cord provided.

÷Do not use a power supply voltage other than that indicated (AC 100 - 120 V, 50/60 Hz) as this may cause fire or electric shock.

÷For the plasma display, a three-core power cord with a ground terminal is used for efficiency protection. Always be sure to connect the power cord to a three-pronged grounded outlet and make sure that the cord is properly grounded. If you use a power source converter plug, use an outlet with a ground terminal and screw down the ground line.

English

Installation and Connections

15

En

Image 21

Contents PDP-503CMXPDP-433CMX English Operating Instructions Safety Precautions Safety PrecautionsImportant Safety Instructions Iii Contents Features Before Proceeding How to Use This ManualScreen Displays Example of PDP-503CMX Screen DisplayPress 5/∞ to select the item to be adjusted Press 5/∞/2/3 to adjust the valueAbout operations in this manual Before Proceeding Press Menu to display the menu screenChecking Supplied Accessories Main Unit Part Names and FunctionsMain unit Operation panel on the main unitRemote Control Unit Inserting the batteries Remote control unitWhen handling the remote control unit Connection Panel Operating range of the remote control unit~ Speaker L terminal Illustration depicts PDP-503CMX modelAudio Input Stereo mini jack Audio Output Stereo mini jackInstallation of the Unit Installation and ConnectionsInstallation using the supplied display stand Installation and ConnectionsRear view diagram PDP-503CMX Wall-mount installation of the unitRear view diagram PDP-433CMX Side view diagramConnection to INPUT1 and INPUT2 When connecting to INPUT2Connection to a personal computer Connection of separate Sync analog RGB SourceWhen connecting to INPUT1 When connecting to INPUT2 When connecting to Output INPUT1Connection of G on Sync analog RGB source Audio Connections Connecting the speakersConnection of composite Sync analog RGB Source Making connections to the audio inputs on this unitControl Cord Connection Power Cord ConnectionHow to Route Cables To attach the speed clamps to the main unitTo remove speed clamps Setup after Connection Setting Up the SystemScreen Mode setup Press 2/3 to select SET UPSetup of Clamp Position Clamp Position setupSetting Up the System Press SET to select LockedOperations Press STANDBY/ON to put this unit in the operation modeSelecting an Input Source Before you begin, make sure you havePress Volume on the remote control unit To adjust the volumePress Muting on the remote control unit Press Display on the remote control unitScreen Size Selection During personal computer signal inputChanging the screen size Press Screen Size to select the sizeSupported only on PDP-503CMX Moving the screen position upward or downwardPartial Image Enlargement Press 5/∞ to select either the Power Automatic Power OFFManagement or Auto Power OFF mode When using InputDisplay Panel Adjustments Adjusting the Picture QualityTo reset Picture mode settings to the default Display Panel Adjustments Adjusting the Image Position and Clock Automatic AdjustmentTo reset Screen mode settings to the default Rewriting the Input Display Other OperationsOther Operations Press SET to select Input LabelPress SET to select Power Control Power Control FunctionPress 2/3 to select Option Press MenuAudio Output Audio OUT Other Operations Press SET to select InputPress 5/∞ to select Audio OUT Troubleshooting CleaningAbout the self diagnosis mode Additional InformationProblems commonly mistaken as breakdown General problemsSTANDBY/ON indicator Panel sticking and after-image lagAdditional cautions General PDP-503CMX AccessoriesGeneral PDP-433CMX Input/outputSupplement 1 -1/2 PDP-503CMX PC signal compatibilty table INPUT1, INPUT2Information AdditionalSupplement 1 -2/2 PDP-433CMX Pin No Input Output Supplement Explanation of Terms