Pioneer PDP 433CMX Operations, Selecting an Input Source, Before you begin, make sure you have

Page 25

Operations

Selecting an Input Source

This section explains the basic operation of this unit. Outlined on the following pages is how to turn the main power on and off, put this unit in the operation or standby mode and how to select connected components.

Before you begin, make sure you have:

•Made connections between this unit and personal computer as described in the section “Installation and Connections” starting on page 10.

•Set up the on-screen menu to input signals from components connected to INPUT1 and INPUT2 as described in the section “Setting Up the System” on page 17.

If no connections are made to these terminals, on-screen setup is not necessary.

2,5

2,5

3

3

4

Main Unit Operating

Remote Control Unit

Panel

 

1Switch MAIN POWER on the main unit to the on position to turn the main power on.

The STANDBY/ON indicator lights red.

2Press STANDBY/ON to put this unit in the operation mode.

The STANDBY/ON indicator turns green.

3Press INPUT on the remote control unit or the main unit to select the input.

Input changes each time the main unit’s INPUT is pressed as follows.

3 INPUT1

INPUT2 2

•When the menu screen is displayed, changing the signal input will cause the menu screen to turn off.

•If the input computer signal is not supported by the display, the following message will be displayed:

I N P U T 1

CA U T I O N

UN S UP P O RT E D S I G N AL

f H : 7 7 . 1 k H z

f V : 8 5 . 0 H z 1 1 5 2 X 8 6 4

F U L L

I N P U T 1

CA U T I O N

OU T OF R AN G E

f H : 7 5 . 7 k H z

f V : 1 2 0 . 0 H z

– – – –

F U L L

4Use VOLUME +/– on the remote control unit to adjust the volume.

If no audio connections are made to this unit, this step is not necessary.

5When viewing is finished, press STANDBY/ON to put the unit in standby mode.

The STANDBY/ON indicator will blink and then remain lit (red) indicating that the standby mode is engaged. Operation is not possible while the STANDBY/ON indicator is blinking (red).

6Switch MAIN POWER on the main unit to the off position to turn the main power off.

The STANDBY/ON indicator may continue to light for a short while even after the main power is turned off. This is a result of residual electric load impressed on the circuitry, and the light will turn off presently.

CAUTION

Please do not leave the same picture displayed on the screen for a long time. Doing so may cause a phenomenon known as “screen burn” which leaves a ghost, or residual, image of the picture on the screen.

19

English

Operations

En

Page 24 Page 26
Image 25
Page 24 Page 26
Contents PDP-503CMXPDP-433CMX English Operating Instructions Safety Precautions Safety PrecautionsImportant Safety Instructions Iii Contents Features Before Proceeding How to Use This ManualScreen Displays Example of PDP-503CMX Screen DisplayPress 5/∞ to select the item to be adjusted Press 5/∞/2/3 to adjust the valueAbout operations in this manual Before Proceeding Press Menu to display the menu screenChecking Supplied Accessories Main Unit Part Names and FunctionsMain unit Operation panel on the main unitInserting the batteries Remote control unit Remote Control UnitWhen handling the remote control unit Connection Panel Operating range of the remote control unit~ Speaker L terminal Illustration depicts PDP-503CMX modelAudio Input Stereo mini jack Audio Output Stereo mini jackInstallation of the Unit Installation and ConnectionsInstallation using the supplied display stand Installation and ConnectionsRear view diagram PDP-503CMX Wall-mount installation of the unitRear view diagram PDP-433CMX Side view diagramConnection to INPUT1 and INPUT2 When connecting to INPUT2Connection to a personal computer Connection of separate Sync analog RGB SourceWhen connecting to INPUT2 When connecting to Output INPUT1 When connecting to INPUT1Connection of G on Sync analog RGB source Audio Connections Connecting the speakersConnection of composite Sync analog RGB Source Making connections to the audio inputs on this unitControl Cord Connection Power Cord ConnectionTo attach the speed clamps to the main unit How to Route CablesTo remove speed clamps Setup after Connection Setting Up the SystemScreen Mode setup Press 2/3 to select SET UPSetup of Clamp Position Clamp Position setupSetting Up the System Press SET to select LockedOperations Press STANDBY/ON to put this unit in the operation modeSelecting an Input Source Before you begin, make sure you havePress Volume on the remote control unit To adjust the volumePress Muting on the remote control unit Press Display on the remote control unitScreen Size Selection During personal computer signal inputChanging the screen size Press Screen Size to select the sizeSupported only on PDP-503CMX Moving the screen position upward or downwardPartial Image Enlargement Press 5/∞ to select either the Power Automatic Power OFFManagement or Auto Power OFF mode When using InputAdjusting the Picture Quality Display Panel AdjustmentsTo reset Picture mode settings to the default Display Panel Adjustments Adjusting the Image Position and Clock Automatic AdjustmentTo reset Screen mode settings to the default Rewriting the Input Display Other OperationsOther Operations Press SET to select Input LabelPress SET to select Power Control Power Control FunctionPress 2/3 to select Option Press MenuOther Operations Press SET to select Input Audio Output Audio OUTPress 5/∞ to select Audio OUT Troubleshooting CleaningAbout the self diagnosis mode Additional InformationProblems commonly mistaken as breakdown General problemsPanel sticking and after-image lag STANDBY/ON indicatorAdditional cautions General PDP-503CMX AccessoriesGeneral PDP-433CMX Input/outputSupplement 1 -1/2 PDP-503CMX PC signal compatibilty table INPUT1, INPUT2Information AdditionalSupplement 1 -2/2 PDP-433CMX Pin No Input Output Supplement Explanation of Terms
Top Page Image Contents